-Move the aircraft and position the nosewheels on the greased steel plates (Ref. TASK 09-10-00-584-002).
(2)
Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
(3)
Pressurize the Green hydraulic system (Ref. TASK 29-10-00-863-001).
Subtask 32-51-00-865-072
C. Table of the circuit breakers used in this procedure: -------------------------------------------------------------------------------
PANEL ------ DESIGNATION ------------------------------------------------------- IDENT. LOCATION------------------
121VU HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY 4GG M36
121VU HYDRAULIC/BRAKING AND STEERING/SYS2/CTL 3GG M35
121VU HYDRAULIC/BRAKING AND STEERING/SYS1/CTL 1GG M34
121VU HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY 2GG M33
Subtask 32-51-00-865-075
D. Open, safety and tag this(these) circuit breaker(s):
------PANEL -------------------------------------------------------DESIGNATION ------------------IDENT. LOCATION
-------------------------------------------------------------------------------121VU ENGINE/ENG2/OIL/PRESS 2EN2 N42 121VU ENGINE/ENG1/OIL/PRESS 2EN1 N40
4. Procedure
_________
(Ref. Fig. 504/TASK 32-51-00-991-009, 505/TASK 32-51-00-991-010, 506/TASK
32-51-00-991-011)
Subtask 32-51-00-220-052
A. Check and record the secondary voltage at the sensor 3GC NOTE : The voltages U1 and U2 are in volts (3V approximately).
____
(1)
On panel 402VU, put the A/SKID & N/W STRG switch in OFF position.
(2)
Disconnect the connector (3) from the RVDT 3GC (1).
1EFF : 001-004, 051-054, 1 32-51-00Page 570 1 1 Aug 01/05R 1 1 1CES 1
Adjustment of the NWS Position - Sensor P/N C24763000, Rudder Trim Angle as
reference
Figure 504/TASK 32-51-00-991-009
1EFF : 001-004, 051-054, 1 32-51-00Page 571 1 1 Aug 01/05R 1 1 1CES 1
Adjustment of the Gear Box P/N C24764000 with Tool M46196, Rudder Trim Angle as
reference
Figure 505/TASK 32-51-00-991-010
1EFF : 001-004, 051-054, 1 32-51-00Page 572 1 1 Aug 01/05R 1 1 1CES 1
Calculated Chart - Sensor P/N 24763000 with tool M46196, Rudder Trim Angle as reference Figure 506/TASK 32-51-00-991-011
R 1EFF : 001-004, 051-054, 1 32-51-00Page 573 1 1 Aug 01/05 1 1 1CES 1
(3)
Connect the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST (F26792000-1) (2) between the connector (3) and the RVDT 3GC (1).
(4)
Connect an AC voltmeter (minimum range: 0-20V, accuracy: 1 mV,
frequency: 50-2000 Hz) to the SECONDARY VOLTAGE connections on the
SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST (2).
(5)
Open the CBs of the BSCU SYS2 (3GG and 4GG).
(6)
Make sure that the CBs of the BSCU SYS1 (1GG and 2GG) are closed.
(7)
On panel 402VU, put the A/SKID & N/W STRG switch in ON position.
(8)
With the captains handwheel, move the steering 75 degrees to the left then 75 degrees to the right then to the zero position.
(9)
Stage 1:
(a)
Make sure that the nose wheel steering handwheels and the rudder pedals are in neutral position. Do not operate them.
(b)
On the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST
(2) set the selector switch to U1.
(c)
Record the voltage (U1)(in AC voltage).
(d)
On the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST
(2) set the selector switch to U2.
(e)
Record the voltage (U2)(in AC voltage).
(f)
Calculate the algebraic value x:
x = (U1 - U2)
(10)
Get the rudder trim calculated value X obtained during Trouble Shooting procedure (Ref. TSM 32-51-00-810-823). On the panel 110VU, set the rudder trim switch to the same value.
(11)
Stage 2:
(a)
Make sure that the nose wheel steering handwheels and the rudder pedals are in neutral position. Do not operate them.
(b)
On the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST
(2) set the selector switch to U1. 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架9(3)
