R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 34-21-22Page 407 1201-220, 1May 01/05 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-220, Post SB 34-1280 For A/C 213-213, Subtask 34-21-22-420-050
A. Installation of the Standby Altimeter (3FN)
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Remove the blanking caps from the electrical connectors (4) and (6).
(4)
Remove the blanking plugs from the line ends (3) and (5).
(5)
Make a loop of the flexible hose and connect the quick-disconnect coupling (5) to the receptacle (3) of the standby altimeter (2).
NOTE : After the connection:
____
-make sure that a colored ring is shown on the quick-disconnect coupling
-pull the connectors to be sure that they are correctly attached.
(6)
Connect the electrical connector (6) to the receptacle (4) of the standby altimeter (2).
(7)
Install the standby altimeter (2) in its housing.
(8) Tighten the screws (1).
Subtask 34-21-22-865-052
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 16FN, 4LF
Subtask 34-21-22-710-050
C. Do the operational test of the instrument and panel integral lighting (Ref. TASK 33-13-00-710-001).
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 34-21-22Page 408 1201-220, 1May 01/05 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-220,
5. Close-up________
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-220,
Post SB 34-1280 For A/C 213-213,
Subtask 34-21-22-410-050
A. Close Access
(1) Install the thermoformed cover on the center instrument panel.
(2) Make sure that the work area is clean and clear of tool(s) and other
items.
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 34-21-22Page 409 1201-220, 1May 01/05 1 1 1CES 1
ALTIMETER - STANDBY (3FN) - ADJUSTMENT/TEST___________________________________________
TASK 34-21-22-820-001
ADJUSTING/ALIGNING/CALIBRATING of the Standby Altimeter
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
34-21-22-000-001 34-21-22-400-001 34-21-25-000-001 34-21-25-400-001 CMM 341027 CMM 342122 Removal of the Standby Altimeter (3FN)Installation of the Standby Altimeter (3FN)Removal of the Metric Altimeter (15FN)Installation of the Metric Altimeter (15FN)
3. Job Set-up__________
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-220,
R Post SB 34-1280 For A/C 213-213,
Subtask 34-21-22-869-050
A. Not Applicable
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-220,
4. Procedure_________
R **ON A/C 001-049, 051-099, 101-105,
Subtask 34-21-22-020-053-A
A. Remove the standby altimeter (Ref. TASK 34-21-22-000-001), and the metric altimeter (Ref. TASK 34-21-25-000-001).
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 34-21-22Page 501 1201-220, 1May 01/05 1 1 1CES 1 Subtask 34-21-22-820-050-A
B. Do a calibration test of the standby altimeter, and the metric altimeter. (Ref. CMM 342122). (Ref. CMM 341027).
Subtask 34-21-22-420-053-A
C. Install the standby altimeter (Ref. TASK 34-21-22-400-001), and the metric altimeter (Ref. TASK 34-21-25-400-001). R **ON A/C 151-199, 201-220,
R Post SB 34-1280 For A/C 213-213, Subtask 34-21-22-020-053
A. Remove the standby altimeter (Ref. TASK 34-21-22-000-001).
Subtask 34-21-22-820-050
B. Do a calibration test of the standby altimeter
(Ref. CMM 342122).
Subtask 34-21-22-420-053
C. Install the standby altimeter (Ref. TASK 34-21-22-400-001).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NAVIGATION 導航2(106)
