R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 34-21-26Page 406 1201-220, 1May 01/05 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-220,
3. Job Set-up__________
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-220,
Post SB 34-1280 For A/C 213-213,
Subtask 34-21-26-865-054
A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and
tagged
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
122VU LIGHTING/INSTL LT/MAIN INST/PNL AND/PED 4LF Y04
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-220,
4. Procedure_________
R **ON A/C 001-049, 051-061, 101-105,
(Ref. Fig. 401/TASK 34-21-26-991-001)
R **ON A/C 062-099, 151-199, 201-220,
Post SB 34-1280 For A/C 213-213,
(Ref. Fig. 401A/TASK 34-21-26-991-001-A)
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-220,
Post SB 34-1280 For A/C 213-213,
Subtask 34-21-26-420-050
A. Installation of the Standby Airspeed Indicator (9FN)
(1) Clean the component interface and/or the adjacent area.
(2) Do an inspection of the component interface and/or the adjacent area.
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 34-21-26Page 407 1201-220, 1May 01/05 1 1 1CES 1
(3)
Remove the blanking caps from the electrical connectors (3) and (6).
(4)
Remove the blanking plugs from the line ends (4) and (5).
(5)
Connect the quick-disconnect couplings (5) of the pressure lines (green and red) to the related connectors (4) of the standby airspeed indicator (2).
NOTE : After the connection:
____
-make sure that a colored ring is shown on the quick-disconnect coupling
-pull the connectors to be sure that they are correctly attached.
(6)
Make sure that the electrical connectors are clean and in the correct condition.
(7)
Connect the electrical connector (6) to the receptacle (3) of the standby airspeed indicator (2).
(8)
Install the Standby Airspeed Indicator (2) in its housing.
(9) Tighten the screws (1). Subtask 34-21-26-865-055
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 4LF
Subtask 34-21-26-710-050
C. Do the operational test of the instrument and panel integral lighting (Ref. TASK 33-13-00-710-001).
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 34-21-26Page 408 1201-220, 1May 01/05 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-220,
5. Close-up________
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-220,
Post SB 34-1280 For A/C 213-213,
Subtask 34-21-26-410-050
A. Put the aircraft back to its initial configuration.
(1) Install the thermoformed cover on the center instrument panel.
(2) Make sure that the work area is clean and clear of tool(s) and other
items.
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 34-21-26Page 409 1201-220, 1May 01/05 1 1 1CES 1
INDICATOR - STANDBY AIRSPEED (9FN) - ADJUSTMENT/TEST____________________________________________________
TASK 34-21-26-820-001
ADJUSTING/ALIGNING/CALIBRATING of the Standby Airspeed Indicator
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
34-21-26-000-001 34-21-26-400-001 CMM 341002 Removal of the Standby Airspeed Indicator (9FN)Installation of the Standby Airspeed Indicator (9FN)
3. Job Set-up__________
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-220,
R Post SB 34-1280 For A/C 213-213,
Subtask 34-21-26-020-053
A. Remove the standby airspeed indicator (Ref. TASK 34-21-26-000-001).
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-220,
4. Procedure_________
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-220,
R Post SB 34-1280 For A/C 213-213,
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NAVIGATION 導航2(109)
