R No specific 1 GENERATOR - GROUND PRESSURE MINI. 100 MB (1.45 PSI)
R TO 1400 MB (20.3 PSI) 36122 1 ADAPTOR-CHARGING,PITOT PROBE 98D34003500000 1 ADAPTER COVER-STATIC PORT
1EFF : 001-049, 051-099, 101-105, 151-199, 1 34-21-00Page 501 1201-212, 214-220, 1Aug 01/05 1 1 1CES 1 B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied from the External Power
3. Job Set-up
__________
Subtask 34-21-00-860-056
A. Aircraft Maintenance Configuration
(1)
Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
(2)
Put the safety barriers in position around the RAT area.
Subtask 34-21-00-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------105VU ELEC/CSM/G /EV AUTO/SPLY 7XE C01 122VU ANTI ICE/PROBES/3/PITOT 3DA3 Z16 122VU ANTI ICE/PROBES/3/STATIC 5DA3 Z14
Subtask 34-21-00-865-052
C. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU NAV/STBY/ALTM 16FN F14
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 34-21-00Page 502 1201-212, 214-220, 1May 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-105, 151-199,
Subtask 34-21-00-420-050
D. Connection of the Ground Pressure Generator
(1) Remove the slip on covers from the static probe and the pitot probe of the standby system.
R (2) Connect the GENERATOR - GROUND PRESSURE MINI. 100 MB (1.45 PSI) TO
R 1400 MB (20.3 PSI) to one standby static probe with the STATIC PORT ADAPTER (98D34003500100) from the ADAPTER COVER-STATIC PORT (98D34003500100).
(3)
Connect the ground pressure generator to the standby pitot probe with the ADAPTOR-CHARGING,PITOT PROBE.
(4)
Seal the Stby probes:
CAUTION : WHEN YOU SEAL THE DRAIN HOLE IN THE PITOT PROBE, DO NOT
_______ SEAL THE HOLE DIRECTLY WITH THE COLORED ADHESIVE TAPE. ALWAYS PUT A PIECE OF PLASTIC ON THE HOLE AND USE THE TAPE TO ATTACH THE PLASTIC. IF YOU SEAL THE DRAIN HOLE DIRECTLY WITH THE ADHESIVE TAPE, THERE IS A RISK THAT SOME OF THE ADHESIVE WILL STAY ON THE HOLE AND COLLECT PARTICLES. THIS CAN SUBSEQUENTLY CAUSE BLOCKAGE OF THE HOLE AND THUS INCORRECT OPERATION OF THE PROBE.
(a)
Seal the drain holes of the pitot probe with a piece of plastic and colored adhesive tape of very bright color.
(b)
Seal the opposite standby static probe with a piece of plastic (see CAUTION above) and with the STATIC PORT COVER (98D34003500103) from the ADAPTER COVER-STATIC PORT (98D34003500103).
(5) Start the ground pressure generator.
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 34-21-00Page 503 1 1 Aug 01/05 1 1 1CES 1 1EFF : 001-049, 051-099, 101-105, 151-199, 1 34-21-00Page 504 1201-212, 214-220, 1Aug 01/05 1 1 1CES 1
R **ON A/C 201-212, 214-220,
R Subtask 34-21-00-420-050-A
R D. Connection of the Ground Pressure Generator
R R (1) Remove the slip on covers from the static probe and the pitot probe of the standby system.
R R R R (2) Connect the GENERATOR - GROUND PRESSURE MINI. 100 MB (1.45 PSI) TO 1400 MB (20.3 PSI) to one standby static probe with the STATIC PORT ADAPTER (98D34003500100) from the ADAPTER COVER-STATIC PORT (98D34003500100).
R R (3) Connect the ground pressure generator to the standby pitot probe with the ADAPTOR-CHARGING,PITOT PROBE.
R R NOTE : The ADAPTOR-CHARGING,PITOT PROBE is on the drain hole. Thus it____ is not necessary to seal the drain hole of the pitot probe.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NAVIGATION 導航2(99)
