(2)
 Get a pressure reducing valve.

 (3)
 Get a bleed valve.

 (4)
 Get an isolation valve.

 (5)
 Get a pressure gage that can read pressures from 0 to 150 psig.

 (6)
 Get a union (1) COUPLING - OXYGEN QUICK DISCONNECT (110111-36).

 (7)
 Assemble the test installation
 (Ref. Fig. 502/TASK 35-10-00-991-002)

 (8)
 Remove the blanking cap of the test port 5755HM.

 (9)
 Connect the installation to the test port 5755HM located on the face of the oxygen cylinder support.

 4. Procedure
_________ Subtask 35-10-00-860-051
 A. Test of the LP Oxygen
 (1)
 On the panel 21VU, push the OXYGEN/CREW SUPPLY pushbutton switch (the OFF legend goes off).

 (2)
 Open the nitrogen source. Use the pressure reducing valve to set the pressure to 130 psig.

 (3)
 Close the isolation valve and the nitrogen source.

 (4)
 Keep the system pressurized for at least one half hour.

 (5)
 Make sure that the value on the pressure gage does not decrease. If the pressure decreases, find the leak with SPECIAL MATERIALS (Material No. 05-004). Replace the defective component. Do the test again.

 (6)
 When the pressure stays stable, open the isolation valve.

 EFF : ALL

35-10-00Page 505

 Test Installation
 Figure 502/TASK 35-10-00-991-002
 EFF :  ALL  35-10-00 Page 506 
Feb 01/98
 CES 

 (7) Open the bleed valve. Subtask 35-10-00-614-050
 B. Disconnect the Test Installation
 (Ref. Fig. 501/TASK 35-10-00-991-001)

 (1)
 Put the blanking cap on the test port 5755HM.

 (2)
 Remove the blanking cap from the regulator. Put it in the oxygen stowage bag (5).

 (3)
 Remove the sealed vinyl bag and the blanking cap from the hose (4).

 (4)
 Install a new seal (3) on the hose.

 (5)
 Install and tighten the hose (4) on the port (2) of the oxygen regulator.

 (6)
 Put the oxygen cylinder in the serviceable condition.

 (a)
 Slowly open the oxygen cylinder valve by 3.5 to 4 turns.

 (b)
 Stop for 90 seconds to let the pressure become stable.

 (c)
 Fully open the oxygen cylinder valve.

 (7)
 Bleed the mask stowage boxes. On each stowage box, at the same time, push and then immediately release:

 -
the PRESS TO TEST AND RESET control slide,

 -
the pressure relief button of the mask regulator. Do this operation two to three times.

 (8)
 On the panel 21VU, release the OXYGEN/CREW SUPPLY pushbutton switch (the OFF legend comes on).

 EFF : ALL

35-10-00Page 507

 5. Close-up
________ Subtask 35-10-00-942-050
 A. Put the aircraft back to its initial configuration.
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 De-energize the aircraft electrical circuits
 (Ref. TASK 24-41-00-862-002).

 Subtask 35-10-00-410-050
 B. Close Access
 (1)
 Close the access door 812.

 (2)
 Remove the access platform(s).

 EFF : ALL

35-10-00Page 508

 TASK 35-10-00-790-001- 01
 Leakage test of the LP oxygen system for the crew with the oxygen cylinder source WARNING : KEEP ALL HYDROCARBONS (FUELS, LUBRICANTS, ETC.) AWAY FROM ALL SOURCE
_______ OF OXYGEN. OXYGEN BECOMES EXPLOSIVE WHEN IT TOUCHES HYDROCARBONS.
 WARNING : CLEAN THE TOOLS AND MAKE SURE YOUR HANDS ARE CLEAN TO PREVENT
_______ CONTAMINATION OF THE OXYGEN SYSTEM.
 CAUTION : PUT DRY, CLEAN, METAL OR PLASTIC PLUGS ON ALL PIPES OR UNITS REMOVED
_______ TEMPORARILY. PUT EACH PIPE OR UNIT IN A SEALED VINYL BAG.
 1. Reason for the Job
__________________
 To make sure that there are no leaks in the oxygen system. Do the test with the oxygen cylinder source.
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific  access platform 2.00 m (6 ft. 7 in.)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM OXYGEN 氧氣(24)