R Deploy Switch Figure 601/TASK 78-31-17-991-300
F EEFF : E E ECES ALL 『E 78-31-17EEE Page 604 Feb 01/05
F 『
E C F M E
E E
E 56-5B E
E E
(2) No play should exist between the bushing and the lever.
NOTE : Determine if play exists between the switch lever and the
____ bushing. This may affect electrical signal while the pivot door is in the deploy condition and may cause deploy signal failure (Ref. TASK 78-31-17-710-002).
-------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
1. Examine the deploy switch for:
A. Damage No damage permitted If you find some damage, replace the deploy switch (Ref. TASK 78-31-17-000-001) and (Ref. TASK 78-31-17-400-001).
2. Examine the trigger for:
A. Damage No damage permitted If you find some damage, replace the defective part (Ref. TASK 78-31-17-000-001) and (Ref. TASK 78-31-17-400-001).
3. Examine the beam electrical harness, for:
A. Cracks None permitted If cracks are found, replace the harness (Ref. TASK 78-31-17-000-002) and (Ref. TASK 78-31-17-400-002).
B. Damage threads None permitted If the connector is damaged replace the harness (Ref. TASK 78-31-17-000-002) and (Ref. TASK 78-31-17-400-002).
F 『 EEFF : ALL E Page 60578-31-17
E E Feb 01/05 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
-------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
C. Bent pins None permitted If the connector has bent pins replace the harness (Ref. TASK 78-31-17-000-002) and (Ref. TASK 78-31-17-400-002).
D. Tightness The blue mark of the deploy switch must be covered by the blue mark of the beam electrical If the blue mark of thepressure switch can beseen, tighten theelectrical connector with
harness connector. softnose pliers.
4. Examine the inner
levers for:
A. Damaged or missing pad No damage permitted and No missing permitted If the lever pad ismissing or damaged, replace the inner lever (Ref. TASK 78-31-17-000-003) and (Ref. TASK 78-31-17-400-003).
B. Corrosion None permitted If the lever has corrosion, replace the inner level (Ref. TASK 78-31-17-000-003) and (Ref. TASK 78-31-17-400-003).
5. Examine the outer
levers and bushing for:
A. Damaged lever or bushing No damage permitted If the lever or bushinghas damage, replace the lever or bushing (Ref. TASK 78-31-17-000-003) and (Ref. TASK 78-31-17-400-003).
F 『 EEFF : ALL E Page 60678-31-17
E E Feb 01/05 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
-------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
B. Corrosion
C. Correct operation
D. Lever and bushing
play
R E. Damaged or missing
R pad
R
R
R
R
R
5. Close-up________
Subtask 78-31-17-410-054
A. Close Access
None permitted
Lever should turn fully and easily
No play should exist between the lever and bushing
No damage permitted
No missing pad permitted If the lever or bushing have corrosion, replace the outer lever or bushing (Ref. TASK 78-31-17-000-003) and (Ref. TASK 78-31-17-400-003).
If the lever is not easyto turn, clean the lever and bushing. if the lever is still not easy to turn, replace the lever and bushing (Ref. TASK 78-31-17-000-003) and (Ref. TASK 78-31-17-400-003).
If there is play betweenthe lever and bushing,replace the lever and bushing (Ref. TASK 78-31-17-000-003) and (Ref. TASK 78-31-17-400-003).
If the pad is missing or damaged, replace the outer lever (Ref. TASK 78-31-17-000-003) and (Ref. TASK 78-31-17-400-003).
NOTE : You should apply a witness line of finish paint EA4 blue 5991
____ (Material No. CP2245) all nuts and connections when you have checked their torques.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EXHAUST 1(54)
