B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors
 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
 Maintenance
 78-31-49-991-305 Fig. 404

 F 『 EEFF : ALL E Page 43078-31-49
 E E May 01/05 E E ECES E E 56-5B E

 F  『
 E  C F M  E
 E  E

 E E

 3. Job Set-up
__________ Subtask 78-31-49-941-079
 A. Safety Precautions
 (1) On the center pedestal, on the ENG panel 115VU:

 (a) Put a warning notice to tell persons not to start the engine.

 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 (3) On the overhead maintenance panel 50VU:

 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b) Put a warning notice to tell persons not to energize the FADEC 1(2).

 Subtask 78-31-49-010-113
 B. Get Access
 (1) Open the fan cowl doors: (Ref. TASK 71-13-00-010-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (2) Put the access platform in position. Subtask 78-31-49-040-104
 C. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041).
 F 『 EEFF : ALL E Page 43178-31-49
 E E Feb 01/98 E E ECES E 4. Procedure

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

_________
 (Ref. Fig. 404/TASK 78-31-49-991-305) Subtask 78-31-49-020-077
 A. Removal of the Lower Supply Pipe of the Right Latch
 (1) Put a container 1 USgal (4 L) under the lower latch of the blocker door.

 (2) Disconnect the lower supply pipe from the lower latch and let the hydraulic fluid drain into the container.

 (3) Remove the nuts and the bolts that attach the flange and the upper half clamp to the upper hydraulic line bracket.

 (4) Remove the bolt and the washer that attach the upper half clamp to the middle hydraulic line bracket.

 (5) Remove the nut and the bolts that attach the double flange and the upper half clamps to the double hydraulic line bracket.

 (6) Remove the bolt and the washer that attach the upper half clamp to the lower hydraulic line bracket.

 (7) Disconnect the lower supply pipe from the hydraulic control unit.

 (8) Remove the lower supply pipe from the forward frame.

 (9) Put protective covers on the pipe ends.

 F 『 EEFF : ALL E Page 43278-31-49
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 INTENTIONALLY BLANK

 F 『 E E Page 43378-31-49
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E

 Lower Supply Pipe of the Right Latch
 Figure 404/TASK 78-31-49-991-305- 12 (SHEET 1)
 F EEFF :  ALL  『E 78-31-49 Page 434 
E  E  Feb 01/98
 E  E
 ECES  E

 Lower Supply Pipe of the Right Latch
 Figure 404/TASK 78-31-49-991-305- 22 (SHEET 2)
 F EEFF :  ALL  『E 78-31-49 Page 435 
E  E  Feb 01/98
 E  E
 ECES  E

 F  『
 E  C F M  E
 E  E

 E 56-5B E
 E E
 TASK 78-31-49-400-044

 Installation of the Lower Supply Pipe of the Right Latch
 WARNING : WEAR A FACE SHIELD WHICH IS RESISTANT TO HIGH PRESSURE JETS WHEN YOU
_______
 WORK ON PRESSURIZED SYSTEMS.

R WARNING : DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU DO:
_______ R - FLUSH IT AWAY WITH CLEAN WATER R - GET MEDICAL AID.
 CAUTION : USE 2 WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS.
_______
 ONE WRENCH TO HOLD THE UNION AND ONE TO LOOSEN OR TIGHTEN THE
 COUPLING NUT. THIS WILL PREVENT DAMAGE TO THE HARDWARE.

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EXHAUST 1(92)