(2) Disconnect the electrical harness from the stow-switch connector.
(3) Remove the three bolts and the nuts which attach the blocker door stow-switch.
(4) Remove the blocker door stow-switch from the aft side of the forward frame.
Subtask 78-31-18-110-050
B. Remove sealant and wipe the zone. WARNING : BEFORE THE USE OF SOLVENT, PROTECTIVE FILM OR SEALANT CAREFULLY
_______ READ THE APPLICABLE "MATERIAL SAFETY DATA SHEET" AND FOLLOW ALL LISTED SAFETY AND HEALTH PRECAUTIONS. USE THESE PRODUCTS IN AN AREA OPENED TO THE AIR AND WEAR PROTECTION GLOVES. THESE PRODUCTS ARE FLAMMABLE AND VAPOR IS DANGEROUS. THEY MAY CAUSE IRRITATION OF EYES, NOSE, THROAT AND SKIN. HIGH CONCENTRATIONS MAY CAUSE WEAKNESS, HEADACHE, NAUSEA, DIZZINESS AND IMPAIRED JUDGEMENT.
F 『 EEFF : ALL E Page 40378-31-18
E E May 01/05 ERE
ECES E F 『 E C F M E E E E 56-5B E
Blocker Door Stow-switch
Figure 401/TASK 78-31-18-991-300
F 『 EEFF : ALL E Page 40478-31-18
E E Feb 01/98 E E ECES E F 『 EEFF : ALL E Page 40578-31-18
F 『
E C F M E
E E
E 56-5B E
E E
R (1) Remove sealant from the stow-switch and the forward frame with
R acetone (Material No. CP1039) or stoddard solvent (Material No.
R CP2011) or ardrox 552 (Material No. CP2559) or turco ind 79 (Material
R No. CP2560) or mag-chem teksol (Material No. CP2566) or degreasol 99R
R (Material No. CP2584) or mag-chem skysol (Material No. CP2656) or
R isopropyl alcohol (Material No. CP1041).
(2) Wipe dry zone with a clean cloth.
E E May 01/05 E E ECES E TASK 78-31-18-400-001
F 『
E C F M E
E E
E 56-5B E
E E
Installation of the Blocker Door Stow-switch (4104KS1,4104KS2,4104KS3,4104KS4)
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific softnose pliers No specific warning notice No specific access platform 1 m (3 ft. 3 in.) No specific Torque Wrench : range 36.00 to 220.00 lbf.in
(0.40 to 2.60 m.daN) HIX3005 1 SAFETY SLEEVE - PIVOTING DOOR ACTUATOR
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP2267 * RTV 106 (Ref. 70-30-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-00-410-040 Closing of the Fan Cowl Doors 78-30-00-081-041 Make the Thrust Reverser Serviceable after
Maintenance 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance 78-31-00-710-042 Operational Test of the Thrust Reverser System 78-32-41-080-040 Removal of the Safety Sleeve from Blocker Door
Actuator
F 『 EEFF : ALL E Page 40678-31-18
E E May 01/05 ERE
ECES E -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
F 『
E C F M E
E E
E 56-5B E
E E
78-32-41-480-001 Installation of the Safety Sleeve on Blocker Door
Actuator 78-32-41-860-001 Manual Deployment of the Blocker Door 78-32-41-860-002 Manual Stowing of the Blocker Door 78-31-18-991-300 Fig. 401
3. Job Set-up
__________
Subtask 78-31-18-860-054
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EXHAUST 1(56)
