R R (a) If there is no continuity: - repair these above wirings. 
R R (b) If there is continuity: - do a check and repair the wirings of the ground signal at rudder trim actuator (10CC) pin A/H and pin B/B, (Ref. ASM 22-67/01).
 B. Do the test given in Para. 3.

 Loss of the Power Supply 26VAC of the Rudder Trim Side 2
 1. Possible Causes_______________
R R R R R R  - ACTUATOR-RUDDER TRIM (10CC) - electronic module - wirings of the 26VAC signal (from the rudder trim actuator (10CC) pin B/G and pin A/A to the first terminal block) - wirings of the ground signal at rudder trim actuator (10CC) pin A/B and pin B/H 
2. Job Set-up Information______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------

AMM  22-91-00-710-001 
AMM  27-22-51-000-001 
R  AMM  27-22-51-000-002 
R 
AMM  27-22-51-400-001 
R  AMM  27-22-51-400-002 
R 
ASM  22-67/01

 3. Fault Confirmation
__________________
 A. Test
Ground Scanning of the AFS
Removal of the Rudder Trim Actuator (10CC)
Removal of the Electronic Assembly of the Rudder Trim
Actuator (10CC)
Installation of the Rudder Trim Actuator (10CC)
Installation of the Electronic Assembly of the Rudder
Trim Actuator (10CC)

 (1) Do the Ground Scanning of the AFS (Ref. AMM TASK 22-91-00-710-001).
 4. Fault Isolation
_______________
 A. If the test gives the maintenance message AFS : 231 XPA BUS BAR: R - replace the electronic module of the rudder trim actuator (10CC) (Ref. R AMM TASK 27-22-51-000-002) and (Ref. AMM TASK 27-22-51-400-002).
R (1) If the fault continues:
 - replace the ACTUATOR-RUDDER TRIM (10CC), (Ref. AMM TASK 27-22-51-000-001) and (Ref. AMM TASK 27-22-51-400-001).
R (2) If the fault continues: R
 - do a check of the wirings of the 26VAC signal (from the rudder trim actuator (10CC) pin B/G and pin A/A to the first terminal block), (Ref. ASM 22-67/01).
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞22-62-00∞∞∞∞∞∞∞∞∞∞Page 223
 May 01/98 CES

R R (a) If there is no continuity: - repair these above wirings. 
R R (b) If there is continuity: - do a check and repair the wirings of the ground signal at rudder trim actuator (10CC) pin A/B and pin B/H, (Ref. ASM 22-67/01).
 B. Do the test given in Para. 3.

 Failure of the Rudder Trim/Reset Circuit of the FAC 1
 1. Possible Causes
_______________
 - FAC-1 (1CC1)

 - P/BSW-RUD TRIM/RESET (8CC)

 - wiring of the RUD TR RES NO MON discrete (from the FAC 1 (1CC1) to the RUD TRIM/RESET pushbutton switch (8CC))

 - wiring of the ground signal at RUD TRIM/RESET pushbutton switch (8CC)

 - wiring of the RUD TR RES NC COM discrete (from the FAC 1 (1CC1) to the RUD TRIM/RESET pushbutton switch (8CC))

 - wiring of the ground signal

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
AMM 22-66-34-000-002 Removal of the FAC (1CC1,1CC2)
 AMM 22-66-34-400-002 Installation of the FAC (1CC1,1CC2)
 AMM 22-96-00-710-001 Operational Test of the AFS
 ASM 22-68/03

 3. Fault Confirmation
__________________
 A. Test
 (1) Do the operational test of the AFS (Ref. AMM TASK 22-96-00-710-001) and read the result for the FAC 1:
 (a) With the RUD TRIM/RESET pushbutton switch (8CC) pushed.

 (b) With the RUD TRIM/RESET pushbutton switch (8CC) released.

 4. Fault Isolation
_______________
 A. If only the first test gives the maintenance message AFS : FAC1/RT RESET SW 8CC:
 - replace the FAC-1 (1CC1), (Ref. AMM TASK 22-66-34-000-002) and (Ref. AMM TASK 22-66-34-400-002).
 (1) If the fault continues:
 - replace the P/BSW-RUD TRIM/RESET (8CC).
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞22-62-00∞∞∞∞∞∞∞∞∞∞Page 225
 May 01/98R
 CES  (2) If the fault continues:
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 AUTO FLIGHT 自動飛行1(100)