for S/N 25451 and up
. pins 1 and 3 (>10 megohms)
. pin 1 and the ground (>10 megohms).
a If the resistance values are out of the specified limits:
_
- replace the N1 sensor (4000EV) (Ref. AMM TASK 77-11-10-000-002) and (Ref. AMM TASK 77-11-10-400-002).
b If the resistance values are in the specified limits:
_
- connect the HJ10 harness to the N1 sensor.
(b) Disconnect connector HJ10 from the ECU (4000KS) receptacle and visually examine the receptacles and the connectors for damaged pins or contamination (Ref. AMM TASK 73-21-50-210-002).
1 If damage is found:
_ - repair or replace as required.
2 If no damage is found:
_
- do the electrical resistance test through the J10 harness between: . pins 16 and 17 (40 to 80 ohms)
for S/N different than 25451 and up
. pins 16 and 6 (>5 kiloohms)
. pin 16 and the ground (>10 megohms)
for S/N 25451 and up
. pins 16 and 6 (>10 megohms)
. pin 16 and the ground (>10 megohms).
F 『 EEFF : ALL E ∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page 212
E E Aug 01/01 ERE ECES
F 『
E C F M E
E E
E 56 E
E E
R a_ If the resistance values are in the specified limits:
R - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001)
R and (Ref. AMM TASK 73-21-60-400-001).
R b_ If the resistance values are out of the specified limits:
R - replace the HJ10 harness (Ref. AMM TASK 73-21-50-000-043)
R and (Ref. AMM TASK 73-21-50-400-043).
R
R B. Do the test given in Para. 3.A.
R (1) No additional maintenance action is required if the fault is not
R confirmed.
R (2) Repeat the fault isolation procedure if the fault continues.
R
F 『 EEFF : ALL E ∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page 213
E E May 01/99 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
TASK 77-10-00-810-814
R Loss of N1 Feedback Signal - Engine 2 - Channel A and Channel B R
1. Possible Causes
_______________
R - SENSOR-N1 ROTATIONAL SPD (4000EV) R - ECU (4000KS) R - HJ9 harness R - HJ10 harness R
2. Job Set-up Information
______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
R No specific bristle brush
R B. Consumable Materials
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R Material No. CP2011 *
R stoddard solvent (Ref. 70-30-00)
R C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 73-21-50-000-042
AMM 73-21-50-000-043
R AMM 73-21-50-210-002
AMM 73-21-50-400-042
AMM 73-21-50-400-043
R AMM 73-21-60-000-001
R AMM 73-21-60-400-001
AMM 73-29-00-710-040
AMM 77-11-10-000-002
AMM 77-11-10-400-002
R
F EEFF : ALL E E ECES Removal of the HJ9 HarnessRemoval of the HJ10 Harness Visual Inspection of the Wiring HarnessesInstallation of the HJ9 HarnessInstallation of the HJ10 Harness Removal of the Electronic Control Unit (ECU) Installation of the Electronic Control Unit (ECU)Operational Test of the FADEC on the Ground (with Engine non Motoring)Removal of the N1 Speed Sensor (4000EV)Installation of the N1 Speed Sensor (4000EV)
『E
∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page 214
E May 01/99EE
F 『
E C F M E
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發(fā)動機指示(119)
