3. Fault Confirmation
__________________
A. Do the operational test of the FADEC 1A and 1B on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
F 『 EEFF : ALL E ∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page 231
E E Aug 01/99 ERE ECES
F 『
E C F M E
E E
E 56 E
E E
4. Fault Isolation
_______________
A. The failure message is generated if both channel A and channel B signals are invalid or out of range.
(1) If the failure messages N2 SNSR, J7, ECU and N2 SNSR, J8, ECU are not
confirmed: R
R (a) No maintenance action is required.
(2) If the failure messages N2 SNSR, J7, ECU and N2 SNSR, J8, ECU are not confirmed but are repetitive:
- disconnect HJ7 harness from the N2 sensor (N2-A connector) and disconnect HJ8 harness from the N2 sensor (N2-B connector).
R (a) Visually examine the receptacles and the connectors for damaged R pins or contamination (Ref. AMM TASK 73-21-50-210-002).
1 If damage is found:
_ - repair or replace as required.
2 If no damage is found:
_
- do a cleaning of the connectors and receptacles using a bristle brush with stoddard solvent (Material No. CP2011) (Ref. AMM TASK 73-21-50-210-002).
(b) If the failure continues during the subsequent flights:
- replace the SENSOR-N2 ROTATIONAL SPD (4001EV) (Ref. AMM TASK 77-11-20-000-002) and (Ref. AMM TASK 77-11-20-400-002).
(c) If the failure continues during the subsequent flights:
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
(d) If the failure continues during the subsequent flights:
- replace the HJ7 harness (Ref. AMM TASK 73-21-50-000-040) and (Ref. AMM TASK 73-21-50-400-040).
(e) If the failure continues during the subsequent flights:
- replace the HJ8 harness (Ref. AMM TASK 73-21-50-000-041) and (Ref. AMM TASK 73-21-50-400-041).
(3) If the failure message N2 SNSR, J7, ECU is confirmed:
- disconnect the HJ7 harness from the N2 sensor (N2-A connector).
R (a) Visually examine the receptacles and the connectors for damaged R pins or contamination (Ref. AMM TASK 73-21-50-210-002).
1 If damage is found:
_ - repair or replace as required.
F 『 EEFF : ALL E ∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page 232
E E Aug 01/99 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
2 If no damage is found:
_ R - do the electrical resistance test through the N2 sensor R (4001EV) (channel A) between:
. pins 1 and 2 (40 to 80 ohms) . pins 1 and 3 (>10 megohms)
R . pin 1 and the ground (>10 megohms).
a If the resistance values are out of the specified limits:
_
- replace the N2 sensor (4001EV) (Ref. AMM TASK 77-11-20-000-002) and (Ref. AMM TASK 77-11-20-400-002).
b If the resistance values are in the specified limits:
_ R - connect the HJ7 harness to the N2 sensor.
R (b) Disconnect connector HJ7 from the ECU (4000KS) receptacle and R visually examine the receptacles and the connectors for damaged R pins or contamination (Ref. AMM TASK 73-21-50-210-002).
1 If damage is found:
_ - repair or replace as required.
2 If no damage is found:
_
- do the electrical resistance test through the HJ7 harness between: . pins 2 and 11 (40 to 80 ohms) . pins 2 and 3 (>10 megohms)
R . pin 2 and the ground (>10 megohms).
a If the resistance values are in the specified limits:
_
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
b If the resistance values are out of the specified limits:
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發動機指示(127)
