2 If no damage is found:
_
- do a cleaning of the connector and receptacle using a bristle brush with stoddard solvent (Material No. CP2011) (Ref. AMM TASK 73-21-50-210-002).
R
R (b) If the failure continues during the subsequent flights:
- replace the SENSOR-N1 ROTATIONAL SPD (4000EV) (Ref. AMM TASK
77-11-10-000-002) and (Ref. AMM TASK 77-11-10-400-002). R
R (c) If the failure continues during the subsequent flights:
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and
(Ref. AMM TASK 73-21-60-400-001). R
R (d) If the failure continues during the subsequent flights:
- replace the HJ10 harness (Ref. AMM TASK 73-21-50-000-043) and (Ref. AMM TASK 73-21-50-400-043).
(3) If the failure message N1 SNSR, J10, ECU* is confirmed: R - disconnect the HJ10 harness from the N1 sensor (N1-B connector).
R (a) Visually examine the receptacle and the connector for damaged R pins or contamination (Ref. AMM TASK 73-21-50-210-002).
1 If damage is found:
_ - repair or replace as required.
2 If no damage is found:
_ R - do the electrical resistance test through the N1 sensor R (4000EV) (channel B) between:
F 『 EEFF : ALL E ∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page 256
E E Aug 01/99 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
. pins 1 and 2 (40 to 80 ohms)
for S/N different than 25451 and up: . pins 1 and 3 (>5 kiloohms)
R . pin 1 and the ground (>10 megohms)
for S/N 25451 and up: . pins 1 and 3 (>10 megohms)
R . pin 1 and the ground (>10 megohms).
a If the resistance values are out of the specified limits:
_
- replace the N1 sensor (4000EV) (Ref. AMM TASK 77-11-10-000-002) and (Ref. AMM TASK 77-11-10-400-002).
b If the resistance values are in the specified limits:
_ R - connect the HJ10 harness to the N1 sensor. R
R (b) Disconnect the HJ10 harness from the ECU (4000KS) and visually R examine the receptacle and the connector for damaged pins or R contamination (Ref. AMM TASK 73-21-50-210-002). R
1 If damage is found:
_ - repair or replace as required.
2 If no damage is found:
_ R - do the electrical resistance test through the HJ10 harness R between:
. pins 16 and 17 (40 to 80 ohms)
for S/N different than 25451 and up: . pins 16 and 6 (>5 kiloohms)
R . pin 16 and the ground (>10 megohms)
for S/N 25451 and up: . pins 16 and 6 (>10 megohms)
R . pin 16 and the ground (>10 megohms).
a If the resistance values are in the specified limits:
_
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
b If the resistance values are out of the specified limits:
_
- replace the HJ10 harness (Ref. AMM TASK 73-21-50-000-043) and (Ref. AMM TASK 73-21-50-400-043).
F 『 EEFF : ALL E ∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page 257
E E Aug 01/99 E E ECES
E F 『 E C F M E E E E 56 E E E B. Do the test given in Para. 3.A.
(1) No additional maintenance action is required if the fault is not confirmed.
(2) Repeat the fault isolation procedure if the fault continues.
F 『 EEFF : ALL E ∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page 258
E E Aug 01/99 ERE
ECES TASK 77-10-00-810-829
F 『
E C F M E
E E
E 56 E
E E
Loss of the Feedback Signal of the N1 Speed Sensor - Engine 2 - Channel A
1. Possible Causes
_______________
- SENSOR-N1 ROTATIONAL SPD (4000EV)
- ECU (4000KS)
- HJ9 harness
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific bristle brush
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發(fā)動機(jī)指示(137)
