F 『
E C F M E
E E
E 56 E
E E
R
R * If the resistance values are out of the specified
R limits:
R - replace the J10 harness (Ref. AMM TASK 73-21-50-000-
R 043) and (Ref. AMM TASK 73-21-50-400-043).
R
R * If the resistance values are in the specified limits:
R - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-
R 001) and (Ref. AMM TASK 73-21-60-400-001).
R D. Do the test given in Para. 3.A.
(1) No additional maintenance action is required if the fault is not
confirmed.
(2) Repeat the fault isolation procedure if the fault continues.
F 『 EEFF : ALL E ∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page A216
E E May 01/03 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
TASK 77-10-00-810-848
Loss of the ECU Cross Channel on Engine 2 - Channel B
1. Possible Causes
_______________
R R - Alternator Stator R - Accessory Gearbox Assembly R - Alternator Rotor R - J10 Harness R - ECU (4000KS)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R AMM 72-63-00-000-003 Removal of the Accessory Gearbox Assembly
R AMM 72-63-00-400-003 Installation of the Accessory Gearbox Assembly
R AMM 73-21-30-000-001 Removal of the Control Alternator
R AMM 73-21-30-400-001 Installation of the Control Alternator
R AMM 73-21-50-000-043 Removal of the HJ10 Harness
R AMM 73-21-50-210-002 Visual Inspection of the Wiring Harnesses
R AMM 73-21-50-400-043 Installation of the HJ10 Harness
R AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)
R AMM 73-21-60-400-001 Installation of the Electronic Control Unit (ECU)
AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with
Engine non Motoring)
R AMM 79-00-00-281-002 Check of the Electrical Master Chip Detector for
R Particles
3. Fault Confirmation__________________
A. Do the operational test of the FADEC 2B on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
4. Fault Isolation
_______________
R A. If the failure message ECU (B CHANNEL) is not confirmed:
R - no maintenance action is required.
R NOTE : This failure message is generated when there is an internal ECU
____
R cross channel fault, control alternator stator contact, or related
R wiring.
R
F 『
∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page A217
EEFF : ALL E
E E May 01/03
E E
ECES E
F 『
E C F M E
E E
E 56 E
E E
R B. If the failure message ECU (B CHANNEL) is not confirmed but is
R repetitive:
R - do a check of the J10 harness connection at the control alternator:
R (1) If the connection is loose:
R - tighten the connection by hand plus one eighth of a turn.
R NOTE : Soft nose pliers may be used if necessary.
____
R (2) If the connection is tight:
R - Disconnect the J10 harness from the alternator stator.
R (a) Visually examine the alternator stator receptacle and the J10
R harness connector for damaged pins or contamination, and the 90.
R elbow of the harness boot for evidence of overheat (Ref. AMM TASK
R 73-21-50-210-002).
R 1_ If harness or alternator stator connector is damaged:
R - repair or replace as required.
R 2_ If no damage is found:
R - remove the Alternator Stator (Ref. AMM TASK 73-21-30-000-R 001).
R - visually examine the alternator stator and rotor for
R evidence of contact.
R a_ If evidence of contact is found, the cause must be
R determined:
R - inspect the alternator rotor nut for proper installation,
R inspect the Electrical Master Chip Detector for particles
R (Ref. AMM TASK 79-00-00-281-002).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發動機指示(162)
