_________________________________
A. Access
(1) Location Zones
305 Left Fuel Tank
405 Right Fuel Tank
B. Procedure
S 494-018
(1)
Install a new head seal O-ring and two new O-ring seals.
S 434-019
(2)
Assemble these parts of the fuel measuring stick:
(a)
The seal boot with the O-ring seal
(b)
The sleeve
(c)
The spring
(d)
The spring retainer
(e)
The bayonet
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-41-11
ALL ú ú 01 Page 405 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500
MAINTENANCE MANUAL
CALIBRATED
ROD FLAPPER VALVE
PIN HEAD SEAL O-RING
O-RING SEAL
SEAL BOOT
O-RING SEAL
SPRING GUIDE
RETAINING SCREW (2 LOCATIONS)
LOCKING PIN
DRIP HOLE
Fuel Measuring Stick Assembly
Figure 402 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-41-11
ALL ú ú 01 Page 406 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
PIN
SCREWDRIVER SLOT
RETAINER LATCH
RETAINER
(VIEWED FROM BELOW THE WING)
Fuel Measuring Stick Assembly
Figure 402 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-41-11
ALL ú ú 01 Page 407 ú Mar 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(f) The calibrated rod.
S 434-032
(3)
Attach the head of the fuel measuring stick with the locking pin.
S 494-020
(4)
Put a plug in the drip hole in the head.
S 424-021
(5)
Put the bayonet assembly into the bottom wing surface.
(a) Make sure the fuel measuring stick is fully extended all of the time.
S 434-022
(6)
Install the two retaining screws in the bayonet.
S 094-023
(7)
Remove the plug from the drip hole if it is installed.
S 864-033
CAUTION: DO NOT USE FORCE TO GIVE THE FUEL MEASURING STICK THE CORRECT
_______ FIT. THE MEASURING STICK CAN BE AT AN INCORRECT LOCATION IF IT DOES NOT FIT. DAMAGE TO THE MEASURING STICK CAN OCCUR IF YOU USE FORCE.
(8)
Carefully push up the fuel measuring stick until it is engaged.
S 864-039
(9)
Turn the head of the fuel measuring stick clockwise and lock it.
TASK 28-41-11-404-024
5. AIRPLANES WITH THE MAGNETIC FLOAT TYPE OF FUEL MEASURING STICKS;________________________________________________________________ Fuel Measuring Stick Installation (Fig. 402)_________________________________
A. Equipment
(1) T5-0497K - spanner wrench, to install the retainer in the housing -drawing available from Kaiser Electroprecision, 17000 South Red Hill Avenue, Irvine, CA 92714 for local fabrication
B. Access
(1) Location Zones
305 Left Fuel Tank
405 Right Fuel Tank
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
28-41-11
ALL ú ú 02 Page 408 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 燃油 FUEL 3(109)
