(10) Set the EFI transfer switch to the BOTH ON 2 position.
(a) Make sure the two EHSIs show the MAP display.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EFIS ú
34-22-00
ú ú 02A Page 505 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
(b) Make sure the two EADIs show the DH value from the right EFIS control panel.
S 865-022
(11) Set the EFI transfer switch back to the NORMAL position.
F. EFIS Brightness Control Test
NOTE: During the EFIS brightness control tests, the display brightness
____ can adjust because of changes in the flight compartment light environment. For example, changes can occur from sunlight or movement of persons in the flight compartment.
S 865-023
(1)
On the two EFIS control panels, push the WXR ON switch to the on position.
S 725-024
(2)
Do a test of the EADI and EHSI BRT controls as follows:
(a)
On the two EFIS control panels, turn the EADI BRT controls counterclockwise, and then clockwise. 1) Make sure the display brightness on each EADI becomes
dimmer and then brighter.
(b)
On the two EFIS control panels, adjust the EADI BRT controls to get the usual brightness level on the two EADIs.
(c)
On the two EFIS control panels, turn the outer EHSI BRT controls counterclockwise, and then clockwise. 1) Make sure the display brightness on each EHSI becomes
dimmer and then brighter.
(d)
On the two EFIS control panels, adjust the outer EHSI BRT controls to get the usual brightness level on the two EHSIs.
(e)
On the two EFIS control panels, turn the inner EHSI BRT control counterclockwise, and then clockwise. 1) Make sure the brightness level of the weather radar test
pattern (raster) on each EHSI becomes dimmer and then brighter.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH EFIS ú
34-22-00
ú ú 01A Page 506 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
2) Make sure the brightness level of the other symbols on the EHSI does not change.
(f) On the two EFIS control panels, adjust the inner EHSI BRT controls to get the usual raster brightness level on the two EHSIs.
S 725-025
(3) Do a test of the EFIS remote light sensors as follows:
(a)
Use black tape to put a cover on the left EFIS remote light sensor, located on the pilot's glareshield, P7. 1) On the left EADI and EHSI, make sure the display brightness
level decreases.
(b)
Use black tape to put a cover on the right EFIS remote light sensor, located on on the pilot's glareshield, P7. 1) On the right EADI and EHSI, make sure the display
brightness level decreases.
(c)
Remove the black tape from the left and right EFIS remote light sensors. 1) Make sure the display brightness on all the display units
goes back to the correct level.
S 725-026
(4) Do a test of the EADI photosensors as follows:
(a)
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 導(dǎo)航 NAVIGATION 1(128)
