P.O. Box 2426 Coppell, TX 75019, OR other suitable instrument
B. References
(1) 34-11-11/401, Pitot-Static Probe
C. Access
(1) Location Zones
101/102 Control Cabin
202 Lower Nose Compartment
208 Forward Cargo Compartment
D. General Probe Condition Check
S 026-018
(1) Remove the pitot-static probe (AMM 34-11-11/401).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-11-11
ALL ú ú 02 Page 601 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
S 216-002
(2)
Visually examine the pitot static probe for damage.
S 216-003
(3)
Visually examine the pitot static probe for material in the static ports, pitot opening, and pitot drain hole.
S 906-005
(4)
Replace the pitot-static probe if one of the conditions is not satisfactory (AMM 34-11-11/401).
E. Aerodynamic Contour Condition Check
S 226-006
(1) Visually examine the static ports as follows (Fig. 601):
(a)
Make sure that the static port edges are perpendicular to the contoured-surface.
(b)
Make sure that the static ports in the probe are not dirty.
(c)
Make sure that the static port edges are not damaged.
SQUARE EDGE ROUNDED EDGE
DAMAGED
Inspection Criteria for Static Ports Figure 601
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-11-11
ALL ú ú 02 Page 602 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
S 226-007
(2) Visually examine the pitot-static probe for nicks, scratches, or other surface defects as follows:
(a)
Make sure that the depth of the defect is less than 0.015 inches within a radius of 0.5 inches of the static ports.
(b)
Make sure that the depth of the defect is less than 0.025 inches on the remaining head section.
(c)
Make sure that the depth of the defect is less than 0.125 inches on the strut section.
S 906-008
(3) Replace the pitot-static probe if one of the conditions is not permitted (AMM 34-11-11/401).
F. Pitot Tip Condition Check
S 226-009
(1) Visually examine the pitot tip for lip flatness as follows (Fig. 602):
(a) Make sure that the lip flatness is less than 0.015 inches.
NOTE: For a new probe, the lip flatness must be 0.004 |0.002
____
inches.
0.015 INCH
15` (REF)
Lip Flatness Figure 602
E48273
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-11-11
ALL ú ú 01 Page 603 ú Mar 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(2) S 226-010Visually examine the pitot tip for an outward flare of the lip (Fig. 603). (a) Make sure that any pitot tip flare is 0.015 inch or less.
(3) S 226-011Visually examine the pitot tip for an inward dent as follows (Fig. 604): (a) Make sure that the dent is less than 0.030 inches. (b) Make sure that the dent is less than 20 percent of the lip circumference.
(4) S 226-012Visually examine the pitot tip for nicks as follows (Fig. 605): (a) Make sure the depth of a nick is less than 0.035 inches when the pitot tip has only one nick. (b) Make sure that the depth of each nick is less than 0.025 inches when the pitot tip has two nicks.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 導航 NAVIGATION 1(57)
