(d)  
Remove the nut, washer and bolt that attach the ring mount strut (vertical) to the ring mount for the right aft mount.

 (e)  
Remove the nut, washer and bolt that attach the ring mount strut (axial) to the ring mount for the right aft mount.

 (f)  
Remove the nut, washer and bolt that attach the ring mount strut (vertical) to the ring mount for the right forward mount.

 (g)  
Remove the nut, washer and bolt that attach the ring mount strut (lateral) to the ring mount for the right forward mount.

 CAUTION: BE CAREFUL WHEN YOU REMOVE THE UPPER SHROUD FROM THE APU
_______ COMPARTMENT. DAMAGE TO THE UPPER SHROUD CAN OCCUR.
 (h)  Carefully remove the upper shroud from the APU compartment.
 S 034-019
 (15) If the upper shroud will be replaced, remove these parts:
 (a)  
Remove the shutoff valve for the cooling air from the upper shroud (AMM 49-51-21/401).

 (b)  
Remove the fuel heater from the upper shroud (AMM 49-31-61/401).

 TASK 49-12-31-404-020
 3. Upper Shroud Installation (Fig. 401)
_________________________
 A. References
 (1)  
AMM 20-10-37/401, Electrical Bonding

 (2)  
AMM 49-11-00/401, APU Power Plant

 (3)  
AMM 49-31-61/401, Fuel Heater

 (4)  
AMM 49-51-21/401, Cooling Air Shutoff Valve

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 49-12-31
 ALL  ú ú 01 Page 408 ú Mar 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
B. Access
 (1)  
Location Zones
 101 Control Cabin (Left)
 205 Electronic Compartment
 701 Tail Compartment
 703 APU Compartment

 (2)  
Access Panels
 1201 Electronic Equipment Access Door
 3701 Stabilizer Trim Access Door
 3804 APU Cowl Door

 C. Procedure
 S 434-022
 (1) If a new upper shroud will be installed, install these parts:
 (a)  
Install the fuel heater to the new upper shroud (AMM 49-31-61/401).

 (b)  
Install the shutoff valve for the cooling air to the new upper shroud (AMM 49-51-21/401).

 S 424-055
 (2)  
Make sure the bleed air duct is temporarily attached in the APU compartment before you install the upper shroud.

 S 424-025

 (3)  
Install the upper shroud in the APU compartment:

 NOTE:____The ring mount struts have different lengths. If you removed the ring mounts, the correct ring mount must be installed on each airplane mounting bracket.
 CAUTION: BE CAREFUL WHEN YOU INSTALL THE UPPER SHROUD INTO THE APU
_______ COMPARTMENT. DAMAGE TO THE UPPER SHROUD CAN OCCUR.
 (a)  
Put the upper shroud into the APU compartment: 1) Lift the upper shroud into the APU compartment. 2) Align the opening in the upper shroud for the compressor

 inlet air with the compressor air duct. 3) Make sure the inspection port for the inlet screen goes through the lightning hole in the horizontal web.

 (b)  
Install the ring mount strut (lateral) to the ring mount for the right forward mount with the nut, washer and bolt.

 (c)  
Install the ring mount strut (vertical) to the ring mount for the right forward mount with the nut, washer and bolt.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 49-12-31
 ALL  ú ú 02 Page 409 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / GTCP85-129 SERIES /737-300/400/500/ ENGINES/MAINTENANCE MANUAL ////////////////////////
(d)  Install the ring mount strut (axial) to the ring mount for the right aft mount with the nut, washer and bolt. 1) Adjust the ring mount strut if it is necessary.
 NOTE: The ring mount strut can be adjusted if there is a
____ clearance problem with the APU lower shroud and the APU access door.
 (e)  
Install the ring mount strut (vertical) to the ring mount for the right aft mount with the nut, washer and bolt.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 AIRBORNE AUXILIARY POWER 1(119)