曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 2) Lift the panel to get access to the components of the
 temperature indication circuit.
 3) Tag and disconnect the wires from the EGT indicator
 terminals on the rear of the indicator case.
 4) Use the wheatstone bridge or the multimeter to find the
 total resistance of the circuit between (and external to)
 the indicator and the thermocouple probe.
 a) The resistance must be 8.000 |0.035 ohms.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 49-11-00
 ALL  ú ú 18 Page 516 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
5) If the resistance is not in the limits, adjust the variable resistor in the tester to get the correct resistance. 6) Remove the wheatstone bridge or the multimeter.
 CAUTION: MAKE SURE YOU CONNECT THE WHITE (CHROMEL) WIRE TO THE
_______ "CR" TERMINAL. MAKE SURE YOU CONNECT THE GREEN (ALUMEL) WIRE TO THE "AL" TERMINAL. THE INCORRECT OPERATION OF THE TESTER CAN OCCUR IF YOU DO NOT CORRECTLY CONNECT THE WIRES.
 7) Connect the wires to the temperature indicator terminals. 8) Attach the instrument panel to the tester with the screws.
 (i)  
Remove the cap from the fuel pressure port (43) on the fuel control unit.

 (j)  
Connect the fuel pressure hose (42) to the fuel pressure port (43) and the fuel pressure coupling (3) on the tester.

 (k)  
Remove the cap from the control-air pressure port (41) on the load control thermostat.

 (l)  
Connect the control-air pressure hose (40) to the control-air pressure port (41) and the control-air pressure coupling (11) on the tester.

 (m)  
Remove the cap from the oil pressure port (39) on the oil pressure switch.

 (n)  
Connect the oil pressure hose (38) to the oil pressure port (39) and the oil pressure coupling (9) on the tester.

 (o)  
Disconnect the electrical connector (37) from the tachometer generator (36).

 (p)  
Connect the electrical cable or test cable assembly (46) to the tachometer generator (36) and the electrical connector (37).

 (q)  
Connect the electrical cable or test cable assembly (46) to the tester receptacle (13).

 S 865-015
 (5)  Prepare to start the APU:
 (a)  Supply the external electrical power to the airplane
 (AMM 24-22-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 49-11-00
 ALL  ú ú 12 Page 517 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / GTCP85-129 SERIES /737-300/400/500/ ENGINES/MAINTENANCE MANUAL ////////////////////////
(b)  Make sure these circuit breakers are closed:
 1) E3-3 Electrical Shelf, APU Control Unit
 2) P6-2 Load Control Center Assembly

 a) MASTER WARN & CONT b) FIRE PROTECTION DETECTION, APU
 3)  P6-3 Load Control Center Assembly a) MASTER CAUTION, ANNUNCIATOR, APU b) DIM & TEST c) INDICATOR, MASTER DIM BUS, BAT d) INDICATOR, MASTER DIM BUS, NO. 1 DC e) INDICATOR, MASTER DIM BUS, NO. 2 DC f) LANDING GEAR, AIR/GND RELAY & LTS
 4)  P6-4 Load Control Center Assembly
 a) CONTROL GENERATOR, APU

 5)  P6-5 Load Control Center Assembly
 a) APU CONT
 b) APU Generator Control Unit
 c) BAT BUS AUTO
 d) GEN PWR CONT

 6)  P18-5 2nd Observer Panel Assemby
 a) HOT BATTERY BUS
 b) SWITCHED HOT BATTERY BUS

 7)  J9 Battery Shield
 a) AUX POWER UNIT START

 S 865-142
 (6)  Make sure these switches on the P5 forward overhead panel are set correctly:
 (a)  
Set the DC selector switch to the BAT position.

 (b)  
Set the AC selector switch to the APU GEN position.

 (c)  
Set the BAT switch to the ON position.

 (d)  
Set the APU BLEED switch to the OFF position.

 (e)  
Momentarily, set one of the two APU GEN switches to the ON position to close the field relay.

 (f)  
Set the No. 1 AFT FUEL PUMP switch to the ON position.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 AIRBORNE AUXILIARY POWER 1(97)