(2)
Open the access door to the actuator for the air inlet door.

 S 225-004

 (3)  
Make sure the air inlet door aligns correctly for the open position:

 S 015-003
 (a)  Measure the position of the air inlet door in the fully open position (Sheet 3).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 49-15-00
 ALL  ú ú 01 Page 501 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / GTCP85-129 SERIES /737-300/400/500/ ENGINES /MAINTENANCE MANUAL ////////////////////////
SEE  A 
AIR DIFFUSER 
DUCT 
SEE  B 
VORTEX 
GENERATOR 
AIR INLET DOOR 
A  FWD 

PRESSURE 
BULKHEAD  AIR 
INLET 
DOOR 
SEE  E 
AIR DIFFUSER 
DUCT

 FWD
ACTUATOR B
SEE C
Air Inlet Door Adjustment
Figure 501 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 49-15-00
 ALL  ú ú 01 Page 502 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.

NUT

Air Inlet Door Adjustment
Figure 501 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 49-15-00
 ALL  ú ú 01 Page 503 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / GTCP85-129 SERIES /737-300/400/500/ ENGINES /MAINTENANCE MANUAL ////////////////////////
VORTEX GENERATOR

Air Inlet Door Adjustment
Figure 501 (Sheet 3)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 49-15-00
 ALL  ú ú 01 Page 504 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(b)  If it is necessary, adjust the pushrod ends: 1) Remove the nuts, washers and bolts that connect the pushrods to the actuator arms. 2) Loosen the locknut of one pushrod end bearing on each pushrod.
 3)  Turn the pushrod ends until the air inlet door aligns in the limits.
 NOTE: The pushrod end will move 0.02 inch (0.5 mm)
____ with one half turn of the pushrod end.
 4)  Tighten the locknuts of the pushrod end bearings.
 5)  Put the pushrods on the actuator arms.
 6)  Install the nuts, washers and bolts that connect the
 pushrods to the actuator arms.
 S 865-005
 (4)  Set these switches on the P5 forward overhead panel:
 (a)  
Remove the DO-NOT-OPERATE tag from the BAT switch.

 (b)  
Set the BAT switch to the ON position.

 (c)  
Remove the DO-NOT-OPERATE tag from the APU master switch.

 (d)  
Set the APU master switch to the OFF position.

 S 225-006
 (5)  Make sure the air inlet door aligns correctly for the closed position:
 (a)  
Measure the position of the air inlet door in the closed position (Sheet 3).

 (b)  
If it is necessary, adjust the pushrod ends. The clearance between the air inlet door and the inlet throat must be correct.

 NOTE: Do not adjust the position of the air inlet door out of
____ the limits for the open position.
 S 905-007
 (6)  Do this task: "Air Inlet Door Switch Adjustment".
 TASK 49-15-00-905-008
 3.  Air Inlet Door Switch Adjustment (Fig. 502)
________________________________
 A.  Access
 (1)  Location Zones
 101 Control Cabin (Left)
 701 Tail Compartment

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 AIRBORNE AUXILIARY POWER 1(130)