module to ON. 2) Make sure the EICAS advisory message OUTFLOW VLV L (or R) is shown.

 (b)  
Put the OPEN/CLOSE switch on the cabin altitude control module to the CLOSE position. 1) Make sure the left (or right) outflow valve position

 indicator on the ECS synoptic page moves to the fully
 closed position.
 2)  Make sure the left (or right) outflow valve position indicator on the altitude control module moves to the fully closed position.
 3)  Release the OPEN/CLOSE switch.
 (c)  Put the OPEN/CLOSE switch in the OPEN position. 1) Make sure the left (or right) outflow valve position indicator on the ECS synoptic page is 0.90 and 0.95.
 2)  Make sure the left (or right) outflow valve position indicator on the cabin altitude control module is near the fully open position.
 3)  Release the OPEN/CLOSE toggle switch.
 S 714-019
 (3)  Do the Landing altitude display test:
 (a)  Monitor the lower elevation limit of the manual landing altitude selection: 1) Set the AUTO SELECT switch on the CPCS selector panel to
 the A position. 2) Turn the LDG ALT knob on the CPCS selector panel fully counterclockwise. 3) Pull the LDG ALT knob out. a) Check that LDG ALT reads -2000 |50 MAN on the main EICAS.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-31-03
 ALL  ú ú 02 Page 404 ú Oct 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 4)  Set the AUTO SELECT switch on the CPCS selector panel to the B position. a) Check that LDG ALT reads -2000 |50 MAN on the main
 EICAS.
 (b)  Monitor the upper elevation limit of the manual landing altitude selection: 1) Turn the LDG ALT knob on the CPCS selector panel fully
 clockwise. a) Make sure that the LDG ALT value is 14000 |50 MAN on the main EICAS.
 2)  Set the AUTO SELECT switch on the CPCS selector panel to the A position. a) Make sure that the LDG ALT value is 14000 |50 MAN on
 the main EICAS.
 3)  Turn the LDG ALT knob on the CPCS selector panel counterclockwise. Stop when the LDG ALT value is approximately equal to the present field altitude on the main EICAS.
 (c)  Push the LDG ALT knob on the CPCS selector panel to the in position.
 S 864-019
 (4)  Disconnect electrical power if it is not necessary (AMM 24-22-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-31-03
 ALL  ú ú 02 Page 405 ú Oct 10/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 OUTFLOW VALVE AC MOTOR - REMOVAL/INSTALLATION
_____________________________________________
 1.  General_______
 A.  There are two tasks in this procedure. There is one task for the removal and one task for the installation of the outflow valve AC motor. The procedure has these parts:
 (1)  
The removal of power to the outflow valves

 (2)  
The removal off the access panel from the aft bulkhead of the bulk cargo compartment

 (3)  
The removal of the outflow valve AC motor

 (4)  
The installation of the outflow valve AC motor

 (5)  
A CMC ground test of the cabin pressure control system

 B.  The removal and installation procedure is the same for the left or the right outflow valve AC motor.
 TASK 21-31-06-004-001
 2.  Outflow Valve AC Motor Removal (Fig. 401)_____________________________
 A.  References
 (1)  
AIPC 21-31-01, Fig. 1

 (2)  
WDM 21-31-13

 (3)  
SSM 21-31-02

 B.  Access
 (1)  Location Zone
 151 Area Aft of Bulk Cargo Compartment, LH
 152 Area Aft of Bulk Cargo Compartment, RH

 C.  Procedure
 S 864-002
 (1)  Open these circuit breakers and attach DO-NOT-CLOSE tags:
 (a)  
P6 Main Power Distribution Panel
 1) 6J28 CABIN PRESS AUTO A
 2) 6J29 CABIN PRESS AUTO B
 3) 6J30 CABIN PRESS CONT L ICU
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 空調 AIR CONDITIONING 1(120)