曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 NOTE:____ If the damage is more than 3 inches long or more than 5-square inches in area, do the Duct Section Replacement task for rigid foam duct.
 (7)  S 348-132Do these steps to prepare the damaged area of the duct:
 WARNING:_______ DO NOT GET SOLVENTS IN YOUR MOUTH, OR IN YOUR EYES, OR ON YOUR SKIN. DO NOT BREATHE THE FUMES FROM SOLVENTS. SOLVENTS ARE HAZARDOUS MATERIALS. REFER TO PRODUCT MATERIAL SAFETY DATA SHEETS (MSDS) AND LOCAL REQUIREMENTS FOR PROPER HANDLING PROCEDURES.
 (a) (b) (c)  Use the solvent and a wiping cloth to clean the damaged area.Sand the damaged area to remove any remaining adhesive and contamination.Use the solvent and a wiping cloth to clean the damaged area.
 (8)  S 348-133Prepare the Fiberglass cloth: (a) Cut two pieces of fiberglass cloth 1/2 inch larger on all sides than the damaged area. (b) Round the corners of the Fiberglass cloth pieces.
 (9)  S 348-134Prepare the resin.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-23-02
 ALL  ú ú 01A Page 821 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 E. Repair the Duct
 S 348-135
 (1)  Apply a thin, smooth layer of resin to the duct where the cloth patch will be applied.
 NOTE: Make sure the area of the resin is a minimum of the size and
____
 shape of the cloth patch.

 S 348-136
 (2)  
Put a piece of cloth on the resin so that it extends beyond the damaged area a minimum of 1/2 inch to all sides.

 S 348-137

 (3)  
Soak the Fiberglass cloth with resin.

 S 348-138

 (4)  
Put a piece of plastic sheet on the cloth and press lightly with a squeegee or with your hand.

 NOTE: Make the cloth smooth from the center to the edges of the
____ cloth to remove bubbles or wrinkles and to remove unwanted resin.
 S 348-139
 (5)  
Remove the plastic sheet from the patch and remove unwanted resin with a wiping cloth.

 S 348-140

 (6)
Follow the same procedure to apply the second piece of cloth.

 S 348-141

 (7)  
Let the resin cure for 24 hours at room temperature.

 S 168-142
 WARNING: DO NOT GET SOLVENTS IN YOUR MOUTH, OR IN YOUR EYES, OR ON YOUR
_______ SKIN. DO NOT BREATHE THE FUMES FROM THE SOLVENTS. SOLVENTS ARE HAZARDOUS MATERIALS. SOLVENTS MAY BE FLAMMABLE OR HARMFUL TO THE ENVIROMENT. REFER TO PRODUCT MATERIAL SAFETY DATA SHEETS (MSDS) AND LOCAL REQUIREMENTS FOR PROPER HANDLING PROCEDURES.
 (8)  Remove unwanted resin from the edges of the patch with a wiping cloth soaked with solvent.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-23-02
 ALL  ú ú 03A Page 822 ú Jun 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 F. Put the Airplane Back to Its Usual Condition
 S 428-144
 (1)  
If insulation was removed from the duct joint, install new insulation.

 S 418-145

 (2)  
Install the panels or other airplane structure removed to gain access to the duct joint.

 TASK 21-23-02-308-146
 8.  Rigid Foam Duct - Structural Repair (Fig. 802)___________________________________
 A. General
 (1)  This procedure gives instructions for making a structural repair to a rigid foam air conditioning duct. A structural repair replaces the rigid foam in the surface of the duct if the damage or deterioration to the rigid foam is greater than 1/4 inch deep and 1 inch long but the inner lining is not damaged.
 B. Consumable Materials
 (1)  
Fiberglass cloth - minimum 0.007 inch thick (MIL-C-9084 Type VIII) -commercially available

 (2)  
Plastic sheet - polyethylene or vinyl (commerically available)

 (3)  
Urethane foam - rigid (BMS 8-133 Type I Grade 20 Form A)

 (4)  
Potting compound - BMS 5-28, Type 19 (Epocast 1619A/B)

 (5)  
Resin - BMS 8-201 Type II (Epocast 50-A)

 (6)  
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 空調 AIR CONDITIONING 1(39)