(7)  
Wiping cloth, lint-free (commercially available)

 C. References
 (1)  AMM 36-00-00/201, Pneumatics - General
 D. Prepare for the Repair
 S 868-176
 (1)  
Remove the pneumatic power (AMM 36-00-00/201).

 S 868-177

 (2)  
On the bleed air control module on the pilots' overhead panel, put the pack control switches in the OFF position.

 S 018-178

 (3)  
Remove the applicable ceiling, sidewall, or floor panels to gain access to the damaged air conditioning duct joint.

 S 028-179

 (4)  
If insulation is installed on the duct joint, remove the insulation.

 S 348-180

 (5)  
Do these steps to prepare the damaged area of the duct:

 (a)  
Cut away the inner lining that has peeled away from the foam.

 (b)  
Examine the rigid foam.

 NOTE: If the foam is damaged, do the procedure to replace a
____
 section of rigid foam duct.

 WARNING: DO NOT GET SOLVENTS IN YOUR MOUTH, OR IN YOUR EYES, OR ON
_______ YOUR SKIN. DO NOT BREATHE THE FUMES FROM SOLVENTS. SOLVENTS ARE HAZARDOUS MATERIALS. SOLVENTS MAY BE FLAMMABLE OR HARMFUL TO THE ENVIROMENT. REFER TO PRODUCT MATERIAL SAFETY DATA SHEETS (MSDS) AND LOCAL REQUIREMENTS FOR PROPER HANDLING PROCEDURES.
 (c)  Use the solvent and a wiping cloth to clean the damaged area.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-23-02
 ALL  ú ú 03A Page 828 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (d)  
Sand the duct joint area to remove any remaining adhesive and contamination.

 (e)  
Use the solvent and a wiping cloth to clean the damaged area.

 S 348-181
 (6)  Prepare the Fiberglass cloth:
 (a)  
Cut two pieces of fiberglass cloth 1/2 inch larger on all sides than the damaged area.

 (b)  
Round the corners of the Fiberglass cloth pieces.

 S 348-182
 (7)  Prepare the resin.
 E. Repair the Inner Lining
 S 348-183
 (1)  Apply a thin, smooth layer of the resin to the damaged area of the duct.
 NOTE: Make sure the area of the resin is a minimum of the size
____
 and shape of the cloth patch.

 S 348-184
 (2)  
Put a piece of cloth on the resin so that it extends beyond the damaged area a minimum of 1/2 inch on all sides.

 S 348-185

 (3)  
Soak the Fiberglass cloth with the resin.

 S 348-186

 (4)  
Put a piece of plastic sheet on the cloth and press lightly with a squeegee or with your hand.

 NOTE: Make the cloth smooth from the center to the edges of the
____ cloth to remove any bubbles or wrinkles and to remove unwanted resin.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 21-23-02
 ALL  ú ú 02A Page 829 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (5)  S 348-187Remove the plastic sheet from the patch and remove unwanted resin with a wiping cloth.
 (6)  S 348-188Follow the same procedure to apply the second piece of cloth.
 (7)  S 348-189Let the resin cure for 24 hours at room temperature.
 S 168-190

 WARNING: DO NOT GET SOLVENTS IN YOUR MOUTH, OR IN YOUR EYES, OR ON YOUR
_______ SKIN. DO NOT BREATHE THE FUMES FROM THE SOLVENTS. SOLVENTS ARE HAZARDOUS MATERIALS. SOLVENTS MAY BE FLAMMABLE OR HARMFUL TO THE ENVIROMENT. REFER TO PRODUCT MATERIAL SAFETY DATA SHEETS (MSDS) AND LOCAL REQUIREMENTS FOR PROPER HANDLING PROCEDURES.
 (8)  Remove unwanted resin from the edges of the patch with a wiping cloth soaked with solvent.
 F. Put the Airplane Back to Its Usual Condition
 S 428-191
 (1)  
If insulation was removed from the duct joint, install new insulation.

 S 418-192

 (2)  
Install the panels or other airplane structure removed to gain access to the duct joint.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 空調 AIR CONDITIONING 1(42)