24-11-01
 ALL  ú ú 11 Page 607 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 ~.............................................................................. | DPI EXTENSION | ................................................................................ | SCAVENGE FILTER | | | | CONDITION | IDG OIL CONDITION | ACTION | ................................................................................ |Visible magnetic or |Oil condition is not |1. Remove the IDG | |non-metallic particles |a factor | (AMM 24-11-01/401). | |in the scavenge filter. | | | |The scavenge filter or | |2. Replace the IDG oil system| |the scavenge filter o-| | heat exchangers and oil | |ring is damaged | | lines. | |(See the steps to examine| | | |the scavenge filter for | |3. Install the IDG | |more data) | | (AMM 24-11-01/401). | 2.........................…......................….............................1
 5) Rub out the next number on the DPI extension decal.
 S 216-011
 (3) Do these steps to examine the scavenge filter.
 WARNING:_______DO NOT LET HOT OIL GET ON YOU. PUT ON GOGGLES AND OTHER
 EQUIPMENT FOR PROTECTION OR LET THE IDG BECOME COOL. HOT
 OIL CAN BURN YOU.
 WARNING:_______DO NOT LET THE OIL STAY ON YOUR SKIN. YOU CAN ABSORB POISONOUS MATERIALS FROM THE OIL THROUGH YOUR SKIN.
 CAUTION: DO NOT LET THE OIL GET ON THE IDG OR OTHER COMPONENTS.
_______ IMMEDIATELY CLEAN THE OIL WHEN IT FALLS ON THEM. OIL CAN CAUSE DAMAGE TO PAINT AND RUBBER.
 (a) Obey the warnings and caution during all of this task.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 24-11-01
 ALL  ú ú 09 Page 608 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  
Remove the scavenge filter (AMM 24-11-04/401).

 (c)  
Do a check for deposits on the IDG scavenge filter element.

 1)  If the scavenge filter element shows a number of moderately scattered, small metallic flakes (bronze or silver colored metal) or flakes of generator insulation, these by-products are the results of normal IDG operation. Do not replace the IDG. a) If there are a large number of nonmetallic particles
 (black epoxy flakes, sleeving, wire strands or other forms of generator insulation with no metallic particles), it should not be necessary to replace the IDG.
 2)  If the filter element shows bright metal deposits that can be clearly specified as chunks or pieces caused by breakage, replace the IDG.
 NOTE: Nonmetallic flakes or slivers caused by normal wear
____ is not cause for removal of the IDG.
 3)  If a large number of small metallic flakes (bronze or silver colored metal) is present on the filter element, replace the IDG. Do the check for a filter element bypass condition.
 NOTE:____Do not clean the filter element. The filter element should be sent with the IDG to the repair facility.
 S 216-033
 (4)  Examine the scavenge filter for a bypass condition.
 NOTE: The conditions that would allow oil to bypass the scavenge
____ filter are damaged O-rings, filter or a collapsed filter.
 (a)  Do these steps if you do not find a scavenge filter with a bypass condition. 1) Install the old filter and tighten the filter cover with
 your fingers.
 NOTE: Do not clean the filter element.
____
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 24-11-01
 ALL  ú ú 09 Page 609 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 2) Replace the IDG (AMM 24-11-01/401).
 S 846-017
 (5)  
Do these steps if you find a scavenge filter with a bypass condition:

 (a)  
Install the old filter and tighten the filter cover with your fingers.

 NOTE: Do not clean the filter.
____
 (b)  
Remove the damaged IDG (AMM 24-11-01/401).

 (c)  
Do the clean IDG external oil cooling system task.

 S 176-034
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 ELECTRICAL POWER 電源 1(39)