NOTE: The clamp track area is where the IDG mounting flange touches
____
 the QAD ring when the IDG is installed.

 (a)  Replace the QAD ring if the worn areas are not equal around the ring (AMM 24-11-08/401).
 S 216-024
 (5)  
Do a check of the tension bolt.

 (a)  
Install the inspection plate or the IDG in the QAD ring (AMM 24-11-01/401).

 NOTE: Install the plate in the same location where the IDG is
____
 installed.

 (b)  
Tighten the tension bolt on the QAD ring to 240-264
 pound-inches (27.1-29.8 N.m).

 (c)  
Hit the QAD ring lightly with a soft mallet.

 NOTE: Only hit the QAD ring between the 4 o'clock and
____ 7 o'clock positions (as seen from the rear).
 (d)  
Measure the torque of the tension bolt.

 (e)  
Make sure the torque is 180 pound-inches (20.3 N.m) or more.

 1)  If the torque is less than 180 pound-inches (20.3 N.m), do these steps: a) Tighten the tension bolt to 240-264 pound-inches
 (27.1-29.8 N.m). b) Hit the QAD ring lightly with a soft mallet.
 NOTE: Only hit the QAD ring between the 4 o'clock and
____ 7 o'clock positions (as seen from the rear).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 24-11-08
 ALL  ú ú 02 Page 604 ú Feb 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 c)  Measure the bolt torque.
 d)  If the torque is less than 180 pound-inches (20.3 N.m), tighten the bolt to 240-264 pound-inches (27.1-29.8 N.m).
 e)  Hit the QAD and check the torque of the tension bolt until the measured torque of the tension bolt does not decrease. Torque the tension bolt to 240-264 pound-inches (27.1-29.8 N.m.).
 (f)  
Tighten the bolt to 240-264 pound-inches (27.1-29.8 N.m).

 (g)  
If the IDG is used, install lockwire on the tension bolt.

 (h)  
Make sure the torque lug centerline on the QAD ring is in the green band or the yellow band. 1) If the torque lug centerline is not in the green or yellow

 band, replace the QAD ring (AMM 24-11-08/401).

 (i)  
If installed, remove the inspection plate.

 S 416-011
 (6)  If the inspection plate is used, install the IDG (AMM 24-11-01/401).
 TASK 24-11-08-206-012
 3.  IDG Quick Attach-Detach (QAD) Ring Tension Bolt Torque Check (Fig. 601)____________________________________________________________
 A.  Standard Tools and Equipment
 (1)  
Mallet - Soft (rubber, fiber, or equivalent)

 B.  
References

 (1)  
AIPC 24-11-01, Fig. 2

 (2)  
AMM 78-31-00/201, Thrust Reverser System

 C.  
Access

 (1)  
Location Zone 412 Engine 1 - Main Gearbox Aft Face 7 o'clock 422 Engine 2 - Main Gearbox Aft Face 7 o'clock 432 Engine 3 - Main Gearbox Aft Face 7 o'clock 442 Engine 4 - Main Gearbox Aft Face 7 o'clock

 (2)  
Access Panel
 415 Left Thrust Reverser Half - Engine 1
 425 Left Thrust Reverser Half - Engine 2
 435 Left Thrust Reverser Half - Engine 3
 445 Left Thrust Reverser Half - Engine 4

 D.  
Procedure

 (1)  
Open the left thrust reverser half (AMM 78-31-00/201).

 S 016-013
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 24-11-08
 ALL  ú ú 02 Page 605 ú Feb 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 226-015
 (2)  Do a check of the tension bolt torque.
 CAUTION: MAKE SURE THAT THE QAD RING DOES NOT BIND OR CATCH WHILE
_______ YOU TIGHTEN THE TENSION BOLT. THIS CAN CAUSE DAMAGE TO THE QAD RING.
 (a)  
Remove the lockwire from the tension bolt.

 (b)  
Tap the QAD ring with a soft mallet or brass drift to center the QAD ring and to prevent false torque readings.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 ELECTRICAL POWER 電源 1(49)