(d)  
Adjust the outer BRT LWR control knob clockwise and counterclockwise. 1) Make sure the lower IDU becomes brighter when you adjust

 the knob clockwise.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 31-61-04
 ALL  ú ú 02 Page 402 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 2)  Make sure the lower IDU becomes dimmer when you adjust the knob counterclockwise.
 (e)  
Turn the BRT LWR control knob to the middle position.

 (f)  
Push the MENU key on a CDU to show the MENU.

 (g)  
Push the line select key (LSK) that is adjacent to <CMC to show the CMC menu.

 (h)  
If <RETURN shows after you push the LSK, push the LSK that is adjacent to <RETURN until you see the CMC MENU.

 (i)  
Push the LSK that is adjacent to <GROUND TESTS to show the GROUND TESTS menu.

 (j)  
Push the NEXT PAGE key, if necessary, until you find the <FLIGHT MANAGEMENT prompt.

 (k)  
Push the LSK that is adjacent to <FLIGHT MANAGMENT to show the FLIGHT MANAGEMENT menu.

 (l)  
Set the FMC switch on the EICAS control panel/FMC switch to the L position. 1) Make sure the CDU shows INHIBITED on the top of the <FMC-R

 prompt.

 (m)  
Set the FMC switch to the R position.

 1)  Make sure the CDU shows INHIBITED on the top of the <FMC-L prompt.
 S 864-036
 (6)  Remove the electrical power if it is not necessary (AMM 24-22-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 31-61-04
 ALL  ú ú 01 Page 403 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 EICAS DISPLAY SELECT PANEL - REMOVAL/INSTALLATION
_________________________________________________
 1.  General_______
 A.  This subject has two tasks. The first task is to remove the EICAS display select panel. The second task is to install the EICAS display select panel. The installation task includes a test of the installation of the select panel.
 B.  The EICAS display select panel is on the right side of the autoflight control panel, P10. The display select panel is held into the P10 panel by two screws.
 TASK 31-61-05-024-032
 2.  EICAS Display Select Panel Removal__________________________________
 A.  Access
 (1)  Location Zone
 222 Control Cabin, RH

 B.  Procedure
 S 864-023
 (1) Open these circuit breakers and attach DO-NOT-CLOSE tags:
 (a)  P7, Overhead Circuit Breaker Panel
 1) 7F9, EIU L
 2) 7F10, EIU C
 3) 7F15, EIU R

 S 024-024
 (2)  Remove the display select panel:
 (a) Remove the screws from the bottom of the P10 panel.
 NOTE: Keep these screws for the select panel installation.
____
 (b)
Pull the select panel until you can get access to the
 electrical connector(s) on the rear of the panel.
 (c) Disconnect the electrical connector(s) from the panel.

 (d)
Install dust caps on the electrical connector(s).

 TASK 31-61-05-424-033
 3.  EICAS Display Select Panel Installation_______________________________________
 A.  References
 (1)  
AMM 24-22-00/201, Manual Control (Apply Power)

 (2)  
AIPC 31-61-05, Fig. 1

 B.  Access
 (1)  Location Zone
 222 Control Cabin, RH

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 31-61-05
 ALL  ú ú 02 Page 401 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 指示/記錄系統 2(157)