CONVERGENCE CROSSES
IDU POSITION PINS
EIU POSITION PINS
PROGRAM PINS
STANDARD CHARACTER SET
CAUTION:
THE IDU SOFTWARE PART NUMBER, EIU SOFTWARE PART NUMBER AND PROGRAM PINS SHOWN ON THIS DISPLAY FORMAT ARE FOR DESCRIPTIVE PURPOSES ONLY. CONSULT WITH THE AUTHORIZED AIRLINE DEPARTMENT FOR THE CORRECT SOFTWARE PART NUMBERS AND PROGRAM PIN CONFIGURATION.
IDS Test Maintenance Display
Figure 61
IDU SOFTWARE PART NUMBER
EIU SOFTWARE PART NUMBER
RASTER
PATCHES
STANDARD CHARACTER SET
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
31-61-00
ALL ú ú 06 Page 86R ú Feb 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
............. .................... ............... IDU Position Octal Representation Primary System Pin States of IDU Position Pins Function of the (1=gnd, 0=nc) Displayed on the IDS Display Unit
1 2 3 Test Format
............. .................... ............... 0 0 0 0 Main EICAS 0 0 1 1 Auxiliary EICAS 0 1 0 2 CAPT PFD 0 1 1 3 CAPT ND 1 0 0 4 F/O ND 1 0 1 5 F/O PFD
............. .................... ...............
C. EIU Position Pins
(1)
Each of the three rack mounted EIU connectors have three pins designated as EIU position pins. These pins are either wired to ground (gnd) or not connected (nc).
(2)
At power up, each EIU will read the coded position pins to determine it's installed position.
(3)
The position pin configuration for the source selected EIU is displayed on the IDS test format as an octal readout, including parity. All six DUs will display one of the following EIU position configurations.
............. .................... ............... EIU Position Octal Representation System Position Pin States of EIU Position Pins of the (1=gnd, 0=nc) Displayed on the IDS Interface Unit 1 2 Parity Test Format ............. .................... ............... 0 1 0 1 EIU Left 1 0 0 2 EIU Center 1 1 1 3 EIU Right ............. .................... ...............
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
31-61-00
ALL ú
ú 09 Page 86S
ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(4) For incorrect parity, or if the decoded position pins do not reflect the source selected EIU position as displayed in the EIU software part number caption, a magenta colored error message is displayed.
D. IDU Software Part Number Display
(1) Indicates the vendor software part number resident in the display units presenting the IDS test format.
E. EIU Software Part Number Display
(1) Indicates the vendor software part number resident in the source selected EIU.
F. IDS Program Pins
(1) The program pin configuration for the source selected EIU is displayed by a fourteen character hexadecimal readout, including parity. If any program pins are invalid, a magenta colored ERROR message is displayed.
(a)
The fourteen hexadecimal numbers represent the status of fifty six program pins. Each one of the hexadecimal characters represents 4 program pins. The status of the program pins can be determined by converting the fourteen hexadecimal numbers to their 4-bit binary representation. A binary 1 represents an enabled program pin. A binary 0 represents a disabled program pin. The four small decimal characters (1, 32, 33, and 56) that encompass the fourteen large hexadecimal characters, help you determine the program pin number.
(b)
The hexadecimal numbers are converted to a 4-bit binary format as follows:
~............................... | HEXADECIMAL | 4-BIT BINARY | ................................. | 0 | 0 0 0 0 | | 1 | 0 0 0 1 | | 2 | 0 0 1 0 | | 3 | 0 0 1 1 | | 4 | 0 1 0 0 | | 5 | 0 1 0 1 | | 6 | 0 1 1 0 | | 7 | 0 1 1 1 | | 8 | 1 0 0 0 | | 9 | 1 0 0 1 | | A | 1 0 1 0 | | B | 1 0 1 1 | | C | 1 1 0 0 | | D | 1 1 0 1 | | E | 1 1 1 0 | | F | 1 1 1 1 | 2...............…...............1
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 指示/記錄系統 2(96)
