(a)
Manually move the uplock hook to the close (gear locked up) position (Fig. 202).
NOTE: You can use the actuating tool or a wood bar to move the
____ uplock hook. If you use a wood bar, put it in the jaw of the uplock hook.
(b)
Make sure the clearance is as shown on Fig. 201.
(c)
Install new shims or or remove laminates from the shims (1) to get the correct clearance.
S 862-057
(2)
Make sure the control handle for the landing gear is in the OFF position.
S 862-084
(3)
Pressurize the No. 4 hydraulic system (Ref 29-11-00/201).
S 862-031
WARNING: MAKE SURE THAT ALL PERSONS AND EQUIPMENT ARE CLEAR OF THE
_______ OPERATION PATH FOR THE LANDING GEAR. FAST MOVEMENT OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(4)
Move the control handle for the landing gear to the DN position.
(5)
Make sure the uplock hook opens and stays open.
S 212-040
NOTE: MANUAL ASSIST CAN BE NECESSARY TO RELEASE THE UPLOCK ASSEMBLY
____ TO THE GEAR DOWN POSITION. THIS MUST BE DONE BEFORE ANY FURTHER HYDRAULIC OPERATION OF THE APPLICABLE GEAR.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-61-21
ALL ú ú 01 Page 207 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
1/2" DIA.
_______THE USE OF THIS TOOL WITH A DAMAGED RUBBER SLEEVE
LOCK/CLOSE
Uplock Actuating Tool Figure 202
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-61-21
ALL ú ú 01 Page 208 ú Feb 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 862-042
(6)
Remove pressure from the No. 4 hydraulic system (AMM 29-11-00/201). S 092-048
WARNING:_______OBEY THE REMOVAL PROCEDURE FOR THE DOOR LOCKS. THE DOORS OPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(7)
Remove the door locks for the main landing gear (AMM 32-00-30/201).
TASK 32-61-21-822-019
5. Adjust the Uplock Sensor for the Wing Gear (Airplane On Jacks)_________________________________________
A. References
(1)
07-11-01/201, Jacking Airplane
(2)
09-11-00/201, Towing
(3)
24-22-00/201, Manual Control
(4)
29-11-00/201, Main Hydraulic Supply System
(5)
32-00-30/201, Landing Gear Door Locks
(6)
32-09-03/501, Proximity Switch Electronics Unit
B.
Access
(1)
Location Zone
135 Wing Landing Gear Wheel Well, LH
136 Wing Landing Gear Wheel Well, RH
C.
Prepare for the Adjustment
S 862-081
(1) Make sure there is no pressure to the No. 4 hydraulic system (Ref 29-11-00/201).
S 492-049
WARNING: MAKE SURE THE GROUND LOCKS ARE INSTALLED ON THE NOSE AND MAIN
_______ LANDING GEAR. AN ACCIDENTAL RETRACTION OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(2) Make sure that ground locks for the nose and main landing gear are installed (Ref 09-11-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-61-21
ALL ú ú 01 Page 209 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 492-050
WARNING:_______OBEY THE INSTALLATION PROCEDURE FOR THE DOOR LOCKS. THE DOORS OPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊 起落架 LANDING GEAR 9(100)
