B.
References
(1)
09-11-00/201, Towing
(2)
24-22-00/201, Manual Control
(3)
29-11-00/201, Main Hydraulic Supply System
(4)
32-00-30/201, Landing Gear Door Locks
(5)
32-09-03/501, Proximity Switch Electronics Unit
(6)
IPC 32-61-02 Fig. 21
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-61-11
ALL ú ú 01 Page 206 ú Jun 10/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
C. Access
(1)
Location Zone
137 Body Gear Wheel Well, Aft Bulkhead, Left Gear
138 Body Gear Wheel Well, Aft Bulkhead, Right Gear
D.
Prepare for the Adjustment
S 862-057
(1)
Supply electrical power (Ref 24-22-00/201).
S 862-104
(2)
Make sure there is no pressure in the No. 1 hydraulic system (Ref 29-11-00/201).
S 492-049
(3)
Make sure that all of the ground locks for the landing gear are installed (Ref 09-11-00/201).
S 492-106
WARNING:_______OBEY THE INSTALLATION PROCEDURE FOR THE DOOR LOCKS. THE DOORS OPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(4)
Do this task: Installation of the Door Locks on the Wing Landing Gear (AMM 32-00-30/201).
S 492-050
(5)
Do this task: Installation of the Door Locks on the Body Landing Gear (AMM 32-00-30/201).
E.
Adjust the Uplock Sensor (Fig. 202)
S 822-037
(1)
Do these steps to adjust the uplock sensor (1):
(a)
Manually move the uplock hook to the closed (gear locked up) position (Fig. 202).
NOTE: You can use the actuating tool or a wood bar to move the
____ uplock hook. If you use a wood bar, put it in the jaw of the uplock hook.
(b)
Make sure the clearance between the sensor and the target is as shown on Fig. 201.
(c)
If the clearance is not correct, do these steps: 1) Remove the sensor from the mounting bracket. 2) Install new shims (4) or remove the laminations from the
shim as it is necessary to get the correct clearance.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-61-11
ALL ú ú 03 Page 207 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
LOCK OPEN
NOTE: ALL DIMENSIONS ARE IN INCHES.
Uplock Actuating Tool Figure 202
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-61-11
ALL ú ú 01 Page 208 ú Oct 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 747-400 MAINTENANCE MANUAL
3) Install the sensor on the mounting bracket.
(2) S 862-041Make sure the control handle for the landing gear is in the OFF position.
(3) S 862-108Pressurize the No. 1 hydraulic system (Ref 29-11-00/201).
(4) S 862-052Move the control handle for the landing gear to the DN position.
(5) S 212-038Make sure the hook opens and stays open.
S 092-040
WARNING: OBEY THE REMOVAL PROCEDURE FOR THE DOOR LOCKS.____
_______ THE DOORS OPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(6)
Do this task: Remove the Door Locks on the Wing Landing Gear (Ref 32-00-30/201).
S 092-051
(7)
Do this task: Remove the Door Locks on the Body Landing Gear (Ref 32-00-30/201).
S 862-039
(8)
Remove the hydraulic pressure from the No. 1 hydraulic system (Ref 29-11-00/201).
S 862-061 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 9(86)
