32-61-22
ALL ú ú 04 Page 212 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
B. Consumable Materials
(1)
C00259 Primer - BMS 10-11, TYPE I
(2)
A00247 Sealant - BMS 5-95
C.
References
(1)
AMM 07-11-01/201, Jacking Airplane
(2)
AMM 07-11-03/201, Jacking Airplane Axles
(3)
AMM 09-11-00/201, Towing
(4)
AMM 29-11-00/201, Main Hydraulic Supply System
(5)
AMM 32-00-30/201, Landing Gear Door Locks
(6)
AIPC 32-61-57 Fig. 21
D.
Access
(1)
Location Zone
735 Wing Landing Gear, LH
745 Wing Landing Gear, RH
E.
Prepare for Adjustment
S 492-030
WARNING: YOU MUST CAREFULLY INSTALL GROUND LOCKS IN ALL LANDING GEAR.
_______ AN ACCIDENTAL RETRACTION OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(1) Make sure you install the ground locks for the main landing gear (AMM 09-11-00/201).
S 492-019
WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO INSTALL
_______ THE DOOR LOCKS ON THE LANDING GEAR DOORS. THE DOORS CAN CLOSE QUICKLY IF YOU DO NOT INSTALL THE DOOR LOCKS CORRECTLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
(2)
Make sure you install the main gear door locks (AMM 32-00-30/201).
S 862-020
(3)
Make sure the control handle for the landing gear is in the DN position.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-61-22
ALL ú ú 05 Page 213 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 582-021
(4) Lift the airplane on jacks until all the wheels are clear of the ground (AMM 07-11-01/201).
S 862-022
WARNING: THE TRUCKS OF THE LANDING GEAR WILL MOVE WHEN THE HYDRAULIC
_______ SYSTEM IS PRESSURIZED. MAKE SURE PERSONS AND EQUIPMENT ARE CLEAR OF THE TRUCK PATH.
(5)
Supply power to the No. 4 hydraulic system (AMM 29-11-00/201).
F.
Adjust the Truck Tilt Sensor
S 222-032
(1)
Measure the clearance between the sensor and the target with the truck in the tilted position.
(a)
Compare the clearance that you found to the clearance that is shown on Fig. 201.
S 862-034
(2) Remove hydraulic power from the No. 4 hydraulic system
(AMM 29-11-00/201).
S 822-031
CAUTION:_______DO NOT REMOVE THE TARGET BRACKET TO ADJUST THE TARGET SHIM. IT IS NOT ALWAYS POSSIBLE TO INSTALL THE BRACKET ACCURATELY AND YOU WILL NOT BE ABLE TO ADJUST THE CLEARANCE CORRECTLY.
(3)
Adjust the sensor clearance:
(a)
Use an axle jack to move the truck to the not tilted position (AMM 07-11-03/201).
NOTE: This will give you access to the target.
____
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-61-22
ALL ú ú 05 Page 214 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(b)
Remove the sensor from the support bracket.
(c)
Install new shims or remove the laminations from the shim as necessary to get the correct clearance.
(d)
Install the sensor on the support bracket.
(e)
Tighten the sensor support hardware.
(f)
Lower the axle jack to let the truck move to the tilted position.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 起落架 LANDING GEAR 9(108)
