(2)  
AMM 12-15-01/301, Main Gear Shock Strut

 (3)  
AMM 24-22-00/201, Electrical Power - Control

 (4)  
AMM 29-11-00/201, Main (Left, Right, and Center) Hydraulic Systems

 (5)  
AMM 32-00-15/201, Landing Gear Doorlocks

 (6)  
AMM 32-00-20/201, Landing Gear Downlocks

 (7)  
AMM 32-11-16/401, Main Gear Torsion Links

 (8)  
AMM 32-11-17/401, Main Gear Truck Assembly

 (9)  
AMM 32-11-19/401, Main Gear Brake Rod

 (10)
 AMM 32-32-00/501, Main Gear Extension and Retraction

 (11)
 AMM 32-32-15/401, Main Gear Truck Positioner Actuator

 (12)
 AMM 32-41-00/201, Hydraulic Brake System

 (13)
 AMM 32-42-00/501, Antiskid/Autobrake System

 (14)
 AMM 32-46-00/501, Brake Temperature Monitoring System

 D.
Access

 (1)  
Location Zones
 211/212 Control Cabin
 731/741 Main Landing Gear (MLG)
 732/742 MLG Body Doors
 733/743 MLG Oleo Doors

 E.
Install the Inner Cylinder

 S 984-005
 (1)  
Put the inner cylinder in position on the truck assembly.

 S 434-006

 (2)  
Install the pin to attach the inner cylinder to the truck assembly (AMM 32-11-17/401).

 S 034-009

 (3)  
Connect the truck positioner actuator to the inner cylinder (AMM 32-32-15/401).

 32-11-25
 ALL  ú ú 01 Page 407 ú Jan 28/00
 
A

757
MAINTENANCE MANUAL

 (4)  S 434-008Connect the brake rods to the inner cylinder (AMM 32-11-19/401).
 (5)  S 494-010Install thread protectors onto the outer cylinder.
 (6)  S 984-011Move the inner cylinder and truck assembly into position under the outer cylinder.
 (7)  S 984-012Align the inner and outer cylinder.
 S 434-013

 CAUTION: MAKE SURE YOU KEEP THE INNER CYLINDER IN THE CENTER OF THE
_______ OUTER CYLINDER AS THE AIRPLANE IS LOWERED. MONITOR THE CLEARANCE BETWEEN THE INNER CYLINDER AND THE OUTER CYLINDER TO MAKE SURE YOU DO NOT CAUSE DAMAGE TO THE INTERNAL COMPONENTS OF THE STRUT.
 (8)  
Carefully lower the airplane (AMM 07-11-01/201). Make sure the fore-and-aft and the inboard-outboard axes stay aligned as the airplane is lowered. Roll the truck assembly forward and aft as necessary to keep the inner cylinder in the center of the outer cylinder as the airplane is lowered.

 S 584-189

 (9)  
Lower the airplane so the lower bearing on the inner cylinder is still outside the outer cylinder.

 S 094-214

 (10)
 Hold the lower bearing and remove the puller assembly.

 S 494-215

 (11)
 Install the ram assembly below the lower bearing.

 (a)  
Attach the slide hammers, if it is necessary.

 32-11-25
 ALL  ú ú 01 Page 408 ú Jun 20/96
 
A

757
MAINTENANCE MANUAL

 S 584-216
 (12)
 Lower the airplane so the lower bearing on the inner cylinder goes into the outer cylinder.

 S 584-217

 (13)
 Move the ram assembly up to push the lower bearing in the outer cylinder, if it is necessary, as you continue to lower the outer cylinder.

 S 094-218

 (14)
 Remove the ram assembly.

 S 094-219

 (15)
 Remove the seal protector and strip from the outer cylinder.

 S 094-220

 (16)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 1(140)