C.
Install the Target Bracket

 S 424-007
 (1)  
Use the two screws to install the target bracket. Tighten the nut to 30-35 pound-inches (Detail A).

 S 844-008

 (2)  
Do the task to measure the clearance between the sensor and target bracket (AMM 32-09-08/201).

 S 824-012

 (3)  
If it is necessary to adjust the clearance, use the adjustment procedure for the target clearance (AMM 32-09-08/201).

 D.
Put the Airplane Back to Its Usual Condition

 S 584-009
 (1)  Lower the airplane and remove the jack if necessary
 (AMM 07-11-02/201).

 32-09-09
 ALL  ú ú 02 Page 403 ú Sep 28/99
 
A

757
MAINTENANCE MANUAL

 S 844-010
 (2)  
If electrical power was supplied to the airplane for the target rigging, do the steps that follow:

 (a)  
Open the access door for the main equipment center, 119BL, (AMM 06-41-00/201) and find the PSEU on the E3 rack.

 (b)  
Push the RESET switch on the front panel of the PSEU to erase the PSEU memory.

 NOTE: The display will flash the code "EEE" while you erase
____
 the PSEU memory.

 (c) Close the access door for the main equipment center 119BL.
 

 32-09-09
 ALL  ú ú 02 Page 404 ú Sep 28/99
 
A

757 MAINTENANCE MANUAL
 MAIN GEAR TILT SENSOR TARGET SUPPORT BRACKET -
______________________________________________ REMOVAL/INSTALLATION
____________________
 1.  General_______
 A.  This procedure contains two tasks. The first task removes the target support bracket for the tilt sensor on the main landing gear. The second task installs the target support bracket for the tilt sensor on the main landing gear.
 TASK 32-09-10-004-004
 2.  Remove the Target Support Bracket for the Tilt Sensor on the Main Landing_________________________________________________________________________ Gear (Fig. 401)____
 A.  References
 (1)  
32-00-15/201, Landing Gear Door Ground Operations and Locking Procedure

 (2)  
32-00-20/201, Landing Gear Downlocks

 B.  
Access

 (1)  
Location Zones
 731/741 Main Landing Gear (MLG)
 732/742 MLG Body Doors
 733/743 MLG Oleo Doors

 C.  
Prepare for the Removal of the Bracket

 S 494-001
 (1)  Make sure the downlocks are installed on the nose and main landing gear (Ref 32-00-20).
 S 494-010
 WARNING: USE THE PROCEDURE IN AMM 32-00-15/201 TO INSTALL THE LOCKS.
_______ THE DOORS OPEN AND CLOSE QUICKLY AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (2)  
Open the doors for the landing gear and install the door locks (Ref 32-00-15).

 (3)  
Install the chocks for the wheel.

 S 494-002
 

 32-09-10
 ALL  ú ú 02 Page 401 ú May 28/01
 
A

757
MAINTENANCE MANUAL

FWD
SEE A
FWD  FOR THE SENSOR TARGET SUPPORT BRACKET
BOLT (2 LOCATIONS) NUT  A 

Truck Tilt Sensor Target Support Bracket Installation for the Main Landing Gear
Figure 401

 32-09-10
 ALL  ú ú 01 Page 402 ú Sep 20/94
 
A

757 MAINTENANCE MANUAL
 D.  Remove the Bracket
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 1(72)