MAIN LANDING GEAR
STA 1111.30
A A
7.
SHIM
8.
NUT
+0.0100
0.0800
-0.0100
9. LOCKWIRE
6. NUT
1. SENSOR 1
1 SENSOR SYSTEM GEAR
LOCATION
NUMBER
FWD
S10059
2
RIGHT
FWD
S10060
1
RIGHT
AFT
S10062
1
LEFT
AFT
S10064
2
LEFT FWD
TRUCK TILT SENSORS
S10697 N/A RIGHT N/A
(RIGHT MAIN LANDING GEAR SHOWN)
2
A
2
NOT INSTALLED ON ALL AIRPLANES
Installation of the Truck Tilt Sensor for the Main Landing Gear
Figure 201
K25633
32-09-07
ALL ú ú 01 Page 203 ú May 28/99
A
757 MAINTENANCE MANUAL
S 032-010
(6)
Remove the sensor mounting screws (2).
S 022-011
(7)
Remove the sensor (1) and pull the sensor wires from the conduit.
NOTE: Make sure you do not pull the end of the line near the splice
____ location for the sensor wires into the conduit.
TASK 32-09-07-402-012
3. Install the Truck Tilt Sensor on the Main Landing Gear (Fig. 201)
_________________________________________________
A. Equipment
(1)
Pin Insertion/Extraction Tool
Part on Crimp Tool Kit - DMC 567
Daniels Manufacturing Corp.
526 Thorpe Road
Orlando, Forida 32824
B.
Consumable Materials
(1)
Braided Lock Stitch - BMS 13-54A
C.
Parts
~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT | FIG | ITEM | ................................................................................ | 201 | 1 | Sensor | 32.09.07 | 01 | 215,265| | | 2 | Screw | | | 30 | | | 3 | Shim | | | 40 | | | 4 | Nuts | | | 35 | 2.......….......…...................................…...........….....…........1
D. References
(1)
AMM 24-22-00/201, Electrical Power - Control
(2)
AMM 32-00-20/201, Landing Gear Downlocks
(3)
Chapter 20, Standard Wiring Practices Manual (SWPM)
E.
Access
(1)
Location Zones
731/741 Main Landing Gear
F.
Install the Truck Tilt Sensor (Fig. 201).
S 432-038
CAUTION:_______DO NOT DROP OR HIT THE SENSORS. YOU CAN CAUSE DAMAGE TO THE INTERNAL COMPONENTS OF THE SENSORS AND CAUSE A FAILURE OF THE AIR/GROUND RELAY SYSTEM.
(1) Twist the sensor wires together.
32-09-07
ALL ú ú 01 Page 204 ú May 28/01
A
757 MAINTENANCE MANUAL
(2) S 862-014If you install a new sensor, do the step that follows: (a) Put a line on the sensor wires.
(3) S 432-042Put the wires through the conduit to the junction box on the truck of the main landing gear.
(4) S 432-043Pull the sensor wire through the conduit into the junction box.
(5) S 432-044Tighten with your hand, the conduit coupling nut to the sensor (1).
(6) S 862-021If you install a new sensor, cut the sensor wire to the correct length (SWPM Chapter 20). (a) Crimp the pins to the sensor wires.
(7) S 432-045Install the sensor wires into the terminal block in the junction box.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 1(62)
