757
MAINTENANCE MANUAL

 S 118-016
 WARNING: DON NOT GET SOLVENTS IN YOUR MOUTH, OR YOUR EYES, OR ON YOUR
_______ SKIN. DO NOT BREATHE THE FUMES FROM SOLVENTS. SOLVENTS ARE HAZARDOUS MATERIALS. REFER TO PRODUCT MATERIAL SAFETY DATA SHEETS (MSDS) AND LOCAL REQUIREMENTS FOR PROPER HANDLING PROCEDURES.
 (1)  
Use solvent, Series 83 (AMM 20-30-83), to do the steps that follow:

 (a)  
Remove the service placard from the door.

 (b)  
Remove the adhesive from the surface of the door.

 TASK 32-21-01-408-011
 3.  Install the Service Placard on the Right Aft Door of the Nose Landing Gear__________________________________________________________________________ (Fig. 801)
 A.  Equipment
 (1)  
Landing Gear Door Locks, (AMM 32-00-15/201).

 B.  
Consumable Materials

 (1)  
B00148 Solvent - Methyl Ethyl Ketone (MEK), TT-M-261

 (2)  
A00247 Sealant, Chromate - BMS 5-95

 (3)  
C00843 Coating, Special Purpose - BAC 5710, Type 41

 C.  
References

 (1)  
AMM 32-00-15/201, Landing Gear Door Locks

 D.  
Access

 (1)  
Location Zones
 711 Nose Landing Gear (NLG)
 713/714 NLG Door Forward
 715/716 NLG Door Aft

 E.  
Install the Service Placard

 S 038-004
 (1)  
Use solvent, Series 92 (AMM 20-30-92) to remove the adhesive from the new placard.

 S 848-005

 (2)  
Use an abrasive material on the aft side of the placard and on the placard location on the door.

 S 398-006

 (3)  
Apply sealant to the surface of the door where the placard will touch.

 (4)  
Put the placard on the door.

 S 848-007
 

 32-21-01
 ALL  ú ú 01 Page 803 ú Sep 28/01
 
A

757 MAINTENANCE MANUAL
 S 398-008
 (5)  
Apply the special purpose coating to the surface of the placard and the filleted areas. Put the sealant 0.25 inch around the outer edge of the placard.

 F.
Put the Airplane Back to Its Usual Condition

 S 098-014
 WARNING:_______OBEY THE REMOVAL PROCEDURE FOR THE DOOR LOCKS. THE DOORS OPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
 (1)  Remove the door locks and close the doors (AMM 32-00-15/201).
 

 32-21-01
 ALL  ú ú 01 Page 804 ú Sep 28/01
 
A

757 MAINTENANCE MANUAL
 NOSE GEAR DRAG STRUT ASSEMBLY - REMOVAL/INSTALLATION
____________________________________________________
 1.  General________
 A.  This procedure contains two tasks. The first task removes the drag strut assembly for the nose landing gear. The second task installs the drag strut assembly for the nose landing gear.
 TASK 32-21-03-004-001
 2.  Remove the Drag Strut Assembly for the Nose Landing Gear (Fig. 401)________________________________________________________
 A.  Equipment
 (1)  
Boom Hoist - A20001-79

 (2)  
Nose Gear Drag Strut Hoist - B32004-1

 B.  
References

 (1)  
AMM 06-41-00/201, Fuselage (Major Zones 100 and 200) Access Doors and Panels

 (2)  
AMM 07-11-02/201, Jacking Airplane Nose

 (3)  
AMM 29-11-00/201, Pressurize/Depressurize Main Hydraulic System

 (4)  
AMM 32-00-15/201, Landing Gear Door Locks
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機(jī)維護(hù)手冊(cè) 起落架 CHAPTER 32 - LANDING GEAR 1(177)