32-12-02
DROP LINK ú
ú 01A ú Page 403May 28/99
A
757
MAINTENANCE MANUAL
S 034-023
(3) Remove the door tang (6) from the main landing gear door.
TASK 32-12-02-404-012
3. Install the Door Tang on the Main Landing Gear (Fig. 401)
______________________________________________
A. Equipment ú (1) Lift Fixture, Engine Accessory - A71015-87
B. Parts
~.............................................................................. | AMM | | AIPC | ................. ............................ | FIG | ITEM | NOMENCLATURE | SUBJECT |FIG | ITEM | ................................................................................ | 401 | 1 | Bolt | 32-12-01 | 02 | 110 | | | 2 | Nut | | | 125 | | | 3 | Bushing | | | 130 | | | 4 | Washer | | | 115 | | | 5 | Washer | | | 120 | | | 6 | Tang Assy | | | 170 | | | 7 | Nut | | | 165 | | | 8 | Bolt | | | 140 | | | 9 | Washer | | | 150 | | | 10 | Bushing | | | 160 | | | 11 | Washer | | | 145 | | | 12 | Washers | | | 155 | 2......…........…...................................…...........…....….........1
C. References
(1)
AMM 32-00-15/201, Landing Gear Door Locks
(2)
AMM 32-12-00/501, Main Gear Doors
D.
Access
(1)
Location Zones
731/741 Main Landing Gear (MLG)
732/742 MLG Body Doors
733/743 MLG Oleo Doors
E.
Install the Door Tang
(1)
Lower the handling equipment.
S 864-014
(2)
Lift the fixture to move the door tang (6) into position for the installation.
S 864-013
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
AIRPLANES WITH TWO PIECE TANG ATTACHMENT ú
32-12-02
DROP LINK ú
ú 01A.1 Page 404
ú Sep 28/02
A
757
MAINTENANCE MANUAL
S 434-024
(3) Install the bushing (3), bolt (1), washers (4, 5) and nut (2) to attach the tang (6) to the forward and aft strut.
NOTE: The bolt (1), washers (4, 5) and nut (2) can be installed in
____ either direction to prevent contact between parts during assembly.
S 434-010
(4) Install the bolt (8), the washers (9, 11, 12), the nut (7) to connect the tang (6) to the forward and aft drop link on the main landing gear door.
NOTE: The bolt (8), washers (9, 11) and nut (7) can be installed in
____ either direction to prevent contact between parts during assembly.
(a) You can move washers (12) from one side of the drop link to the other to satisfy these conditions during installation: 1) To prevent the application force between the drop link and
the clevis on the tang (6) when the door is closed (a minimum of .005 inch gap is necessary between the drop link and the clevis on the tang when the door is closed).
2) To adjust the clearances at the forward and aft edges of the tang (6).
(b)
Use approximately 10 to 12 washers (12) to get the minimum clearance of .005 inch between the drop link and the clevis on the tang (6).
F.
Put the Airplane Back to Its Usual Condition
S 094-017
(1)
Remove the handling equipment and the lift fixture.
S 824-020
(2)
Adjust the door for the main landing gear and adjust the door tang (AMM 32-12-00/501).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 1(156)
