S 034-009
(5)
Remove the nut with the crowfoot wrench.
(a)
Install the thread protector.
32-11-05
ALL ú ú 01 Page 403 ú May 28/99
A
757 MAINTENANCE MANUAL
(b) Remove the pin to disconnect the upper side strut from the upper swivel (View B-B).
S 024-010
(6) Lower the upper side strut and remove it.
TASK 32-11-05-404-037
3. Install the Upper Side Strut for the Main Landing Gear______________________________________________________
A. Equipment
(1)
Drag Strut and Side Strut Sling Equipment, MLG
(components of A32008-52)
(a)
Adapter - A32008-6
(b)
Clamp - A32008-38
(2)
Thread Protector Set, MLG - B32011-14
(3)
Crowfoot Wrench - F70312-38
B.
Consumable Materials
(1)
C00174 Corrosion Preventive Compound -MIL-C-16173, grade 4
(2)
D00633 Grease - BMS 3-33 (Recommended)
(3)
D00013 Grease - MIL-G-23827 (Alternative)
C.
References
(1)
AMM 07-11-01/201, Jacking Airplane
(2)
AMM 32-00-15/201, Landing Gear Door Locks
(3)
AMM 32-11-22/401, Main Gear Downlock Springs
D.
Access
(1)
Location Zones
731/741 Main Landing Gear (MLG)
732/742 MLG Body Doors
733/743 MLG Oleo Doors
E.
Install the Upper Side Strut for the Main Landing Gear.
S 494-011
(1)
Install the sling equipment on the upper side strut. Use the instructions supplied with the tool.
S 584-012
(2)
Lift the upper side strut into the correct position on the main landing gear.
S 624-013
(3)
Apply the corrosion preventive compound to the inner diameter of the two pins.
32-11-05
ALL ú ú 01 Page 404 ú Jan 28/00
A
757 MAINTENANCE MANUAL
S 434-014
(4)
Install the thread protector.
(a)
Apply grease to the pin, the washers, the nuts, and the antirotation bolt.
(b)
Install these parts to connect the upper side strut to the upper swivel.
(c)
Use the crowfoot wrench to tighten the nut to 70-90 pound-feet. Loosen to the nearest lock position to install the antirotation bolt (View B-B).
S 424-015
(5)
Install the thread protector.
(a)
Apply grease to the pin, the washers, the nuts, and the antirotation bolt.
(b)
Install these parts to connect the upper side strut, the downlock assembly, the spring retainer, and the lower side strut.
(c)
Tighten the nut to 70-90 pound-feet. Loosen to the nearest lock position to install the antirotation bolt (View A-A).
S 094-016
(6)
Remove the sling equipment.
F.
Put the Airplane Back to Its Usual Condition
S 414-017
(1)
Install the downlock springs (AMM 32-11-22/401).
S 644-018
(2)
Lubricate the strut at the grease fittings.
S 584-019
(3)
Lower the airplane and remove the jacks (AMM 07-11-01/201).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 1(92)
