曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

The entry to the climb is similar to the entry from cruise
airspeed with the exception that the power must be increased
when the pitch attitude is raised. [Figure 5-64] Power added
after the pitch change will show a decrease in airspeed due
to the increased drag encountered. Power added prior to a
pitch change will cause the airspeed to increase due to the
excess thrust.
Constant Rate Climbs
Constant rate climbs are very similar to the constant airspeed
climbs in the way the entry is made. As power is added,
5-48
Figure 5-65. Constant Rate Climbs.
smoothly apply elevator pressure to raise the yellow chevron
to the desired pitch attitude that equates to the desired vertical
speed rate. The primary instrument for pitch during the initial
portion of the maneuver is the ASI until the vertical speed
rate stabilizes and then the VSI tape becomes primary. The
ASI then becomes the primary instrument for power. If any
deviation from the desired vertical speed is noted, small
pitch changes will be required in order to achieve the desired
vertical speed. [Figure 5-65]
When making changes to compensate for deviations in
performance, pitch, and power, pilot inputs need to be
coordinated to maintain a stable flight attitude. For instance,
if the vertical speed is lower than desired but the airspeed is
correct, an increase in pitch will momentarily increase the
vertical speed. However, the increased drag will quickly
start to degrade the airspeed if no increase in power is made.
A change to any one variable will mandate a coordinated
change in the other.
Conversely, if the airspeed is low and the pitch is high, a
reduction in the pitch attitude alone may solve the problem.
Lower the nose of the aircraft very slightly to see if a power
reduction is necessary. Being familiar with the pitch and
power settings for the aircraft aids in achieving precise
attitude instrument flying.
Leveling Off
Leveling off from a climb requires a reduction in the pitch
prior to reaching the desired altitude. If no change in pitch
is made until reaching the desired altitude, the momentum
of the aircraft causes the aircraft to continue past the desired
altitude throughout the transition to a level pitch attitude. The
amount of lead to be applied depends on the vertical speed
rate. A higher vertical speed requires a larger lead for level
off. A good rule of thumb to utilize is to lead the level off
by 10 percent of the vertical speed rate (1,000 fpm ÷ 10 =
100 feet lead).
To level off at the desired altitude, refer to the attitude display
and apply smooth forward elevator pressure toward the desired
level pitch attitude while monitoring the VSI and altimeter
tapes. The rates should start to slow and airspeed should
begin to increase. Maintain the climb power setting until the
airspeed approaches the desired cruise airspeed. Continue to
monitor the altimeter to maintain the desired altitude as the
airspeed increases. Prior to reaching the cruise airspeed, the
power must be reduced to avoid overshooting the desired
speed. The amount of lead time that is required depends on
the speed at which the aircraft accelerates. Utilization of the
airspeed trend indicator can assist by showing how quickly
the aircraft will arrive at the desired speed.
5-49
Figure 5-66. The top image illustrates a reduction of power and descending at 500 fpm to an altitude of 5,000 feet. The bottom image
illustrates an increase in power and the initiation of leveling off.
To level off at climbing airspeed, lower the nose to the
appropriate pitch attitude for level flight with a simultaneous
reduction in power to a setting that will maintain the desired
speed. With a coordinated reduction in pitch and power there
should be no change in the airspeed.
Descents
Descending flight can be accomplished at various airspeeds
and pitch attitudes by reducing power, lowering the nose to
a pitch attitude lower than the level flight attitude, or adding
drag. Once any of these changes have been made, the airspeed
will eventually stabilize. During this transitional phase, the
only instrument that will display an accurate indication of
pitch is the attitude indicator. Without the use of the attitude
indicator (such as in partial panel flight), the ASI tape, the VSI
tape, and the altimeter tape will show changing values until
the aircraft stabilizes at a constant airspeed and constant rate
of descent. The altimeter tape continues to show a descent.
Hold pitch constant and allow the aircraft to stabilize. During
any change in attitude or airspeed, continuous application of
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Instrument Flying Handbook儀表飛行手冊上(107)