曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

D. Carefully un-tie shade string from tension assy. Assure that all components (ball chain,
spring, shrink tube, loop clamp, & stop nut) are stored in a safe location to prevent
damage or loss of parts during service.
E. Upper blind mod. is attached with two or three screws and stop nuts depending on size,
remove stop nuts to free blind upper rail.
F. Slide blind mod lower rail to top of reveal to free glides from slide track, thus freeing
blind mod. from reveal.
PAGE 4002
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
CLEANING
TASK 25-23-08-100-801
1. General
A. A full cleaning is necessary before each accurate inspection to find the correct location
and the extent of the damage.
B. Cleaning removes all the remaining particles, which can have an unwanted effect on the
performance of the equipment. It also helps the possible repair.
TASK 25-23-08-940-802
2. Job set-up information
A. Tools, Fixtures, equipment and materials
NOTE: Refer to “SPECIAL TOOLS, FIXTURES, EQUIPMENT AND MATERIALS”
for full details on the items used.
REFERANCE QTY NAME
#PC-10 AR NOVUS PLASITC POLISH
BRILLIANIZE AR CLEANER & POLISH
39139 (Prepsol) AR CLEANER FOR NON-FABRIC PARTS
PAGE 5001
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
TASK 25-23-08-100-802
3. Procedure
A. How to use Novus Plastic Polish No. 1
Remove surface dust with soft
evenly and buff with a clean, soft, lint-free cloth.
B. How to use BRILLIANIZE Cleaner & Polish
Shake contents firmly and apply evenly to
cloth. Shake bottle contents and apply a light mist. Spread
any hard, shiny, non-absorbent surface at room
temperature. Rub gently. Before surface dries, polish with a dry lint-free cloth or nondamaging
material, until the surface feels “as smooth as ice”.
FIGURE 5/ GRAPHIC 25-23-08-991-005
PAGE 5002
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
C. Mask fabric
The lustrous feel of Ultra Suede HPC can be maintained by a light brushing with a
medium bristle brush. In the event of a mishap, stains can be removed with detergent. Only when
required use a mild cleaning fluid from your local hardware store.
Everyday Stains: Remove any free matter with knife or spoon. Pat the stained area with
water and mild detergent. Remove detergent solution with a clean cloth and water. Dry on warm
setting with hair dryer or naturally in the air.
Extremely Tough Stains: For severe stains such as automotive grease use a mild solvent.
Moisten a clean cloth with a mild cleaning fluid. Pat the stained area until clean. Blot with a
clean, dry cloth.
D. Shade fabric
Lou Martin easy-glide shade systems utilize a metallized fabric, which is inherently antistatic.
They actually repel dust and seldom require cleaning. An occasional light sweep of a
vacuum is all that should be needed.
In the event of a mishap, Lou Martin easy-glide shades may be cleaned with a mild
detergent and water. However, water spotting can occur. If a detergent is required, we suggest a
mild detergent such as woolite.
NOTE: Do not use ammonia cleaners near the Lou Martin easy-glide shade.
Ammonia cleaners will damage the shade.
PAGE 5003
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
PAGE INTENTIONALLY LEFT BLANK
PAGE 5004
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
TASK 25-23-08-200-801
AIRWORTHINESS LIMITATIONS
1. General
A. The Airworthiness Limitations section is FAA-approved and specifies maintenance
required under §§43.16 and 91.403 of the Federal aviation regulations, unless an
alternative program has been FAA approved.
PAGE 6001
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
PAGE INTENTIONALLY LEFT BLANK
PAGE 6002
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
INSPECTION/REPLACEMENT & REPAIR
TASK 25-23-08-300-801
1. General
A. The procedures given in these chapters are general inspection and repair procedures and
are not applicable to the riveted or welded parts. The manufacturer must repair the riveted
or welded junctions, which are damaged.
TASK 25-23-08-940-803
2. Job set-up information
A. Tools, fixtures, equipment and materials
B. It is recommended that the completion center contact Lou Martin & Assoc., Inc. for
replacement parts to insure quality and operation
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料8(31)