曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Isolation”
G. Attach new inner lens to window assy. Match drill lens with existing nut plate locations.
Note: when drilling assure not to damage nut plates located on backside of reveal.
Then remove clamps. (See “ASSEMBLY”, section 4 page 8002)
FIGURE 8/ GRAPHIC 25-23-08-991-008
PAGE 7005
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
ASSEMBLY
TASK 25-23-08-400-801
1. General
A. Before the assembly, make sure that the CLEANING and the INSPECTION/REPAIR
procedures of all parts are done.
B. Where it is possible, it is recommended to use new parts and genuine approved parts.
TASK 25-23-08-940-804
2. Job set-up information
A. Tools, Fixtures, equipment and materials
NOTE: Refer to SPECIAL TOOLS, FIXTURES, EQUIPMENT AND MATERIALS for
full details on the items used.
REFFERENCE QTY NAME
MS21044-N08 AR Replacement stop nut
MS21044-N06 AR Replacement stop nut
MS51092-6 AR Replacement washer
MS24693S-632 AR Replacement screw
MS24693S-832 AR Replacement screw
PAGE 8001
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
TASK 25-23-08-440-801
3. Blind mod. Reattachment
A. Reinsert the lower rail glides into their slide tracks at top of reveal and slide down approx
half way.
B. Reattach upper blind mod. to the reveal by inserting the upper rail’s screws thru the two
existing holes in the top of the reveal cavity, and secure with MS21044-N04 or
MS21044-N06 stop nuts.
NOTE: Assure a proper attachment with a min. two threads protruding thru nylon
nut.
C. Rethread shade string thru eyelets at bottom of reveal and reattach string to spring & ball
chain.
D. Slide shrink tube & loop clamp over & past spring catch, re-connect spring and ball
chain.
E. To adjust tension to desired level see (“Testing and Fault Isolation, section 3 page 1003)
E. Slide loop clamp & shrink tube to cover tension assy
F. Re-attach loop clamp to retainer clip and secure in place w/ MS21044-N06 stop nut.
TASK 25-23-08-440-802
4. Inner lens reattachment
A. Reattach inner lens with MS24693S-832 screw and pick-up existing nut plate (8 places)
B. Remove protective film from inboard side of lens prior to reattaching decorative mask.
PAGE 8002
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
TASK 25-23-08-440-803
5. Decorative mask reattachment
A. Place the mask over the window assy. and align decorative handle’s holes with the lower
blind mod. attachment holes and attach using MS24693S-632 screw (2)
B. Align the attachment holes of the backside of reveal with those of the decorative mask,
attach decorative mask with MS27039-832 screw pick-up existing insert (5 places)
PAGE 8003
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
FITS AND CLEARANCES
TASK 25-23-08-820-801
1. General
A. The listed clearances are to insure the window is properly installed into the aircraft
TASK 25-23-08-820-802
2. Clearances
A. Assure a min. clearance of .063 in. (1.59 cm) between the window shade assy. and
existing structure.
B. Assure a min. clearance of .13 in. (3.18 cm) between the window assy’s outer lens and
the inboard side of the aircraft’s existing pressure lens.
C. Assure a min. clearance of .04 in. (1.02 cm) between each decorative mask fwd & aft in
the aircraft.
PAGE 9001
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
PAGE INTENTIONALLY LEFT BLANK
PAGE 9002
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
SPECIAL TOOLS, FIXTURES, EQUIPMENT
TASK 25-23-08-940-805
1. Special tools, fixtures and equipments
No special tools, fixtures and equipment are necessary for the maintenance or the overhaul to be
performed on the standard equipment.
Standard tools are used for these operations.
PAGE 10001
JAN 10/05
Lou Martin & Assoc., Inc.
Component Maintenance Manual
25-23-08
STORAGE
TASK 25-23-08-940-806
1. General
A. When any of the window assay’s need to be removed from the aircraft, Lou Martin &
Assoc., Inc. recommends to stow the shade is in the up position.
B. Store in a sheltered, ventilated place with normal hygrometric degree (70%)
C. Cover the window unit with large clean plastic bags or equivalent to protect it from dust
and other airborne particles.
D. On the outside of the bag or cover add a tag with its location in the aircraft for tracking
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料8(33)