曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

20  defines 20 Checklist items for the third Checklist
12  defines 12 Checklist items for the forth Checklist
20  defines 20 Checklist items for the fifth Checklist
Then it has to follow a blank line
Now you write the Headline, name of the Checklist (here TEST-1)
Then the above defined 4 Checklist items have to follow.
This part has to be done for each Checklist, ever starts with a blank line (space holder).
VERY IMPORTANT is that you use the style of 32 letters for each line (Headline and Check items),
if not the Checklist will look a bit chaotic.
So just fill ever shorter lines with space or dots like below, that’s why I changed the back colour to display
the writing structure.
3
5
14
3
TEST-1
Speedbrake . . . ARMED & GREEN .
Gear . . . . . .DOWN & 3 GREEN .
Flaps. . . . . . . SET & GREEN .
NAV Display. . . . . . . . SET .
Course Arrow . . . AS REQUIRED .
TEST-2
Anti-Ice . . . . . AS REQUIRED .
Trim Air Switch. . . . . . OFF .
Press. . . . . . . AS REQUIRED .
ENG-1 Starter. . . . . . . OFF .
ENG-2 Starter. . . . . . . OFF .
APU. . . . . . . . AS REQUIRED .
Exterior Lights. . AS REQUIRED .
Autobrake. . . . . . . . . OFF .
Speedbrake . . . . DOWN DETENT .
Flaps. . . . . . . . . . . .UP .
Radar. . . . . . . . . . . OFF .
Transponder. . . . . . . . OFF .
Landig Lights. . . . . . . OFF .
Taxi Lights. . . . . . . . .ON .
TEST-3
Anti-Ice . . . . . . . . . OFF .
Trim Air Switch. . . . . . .ON .
Press. . . . . . . . . . . OFF .
www.technicalservicerichter.com Page 55
Manual Changes in FSUIPC Module
4) For Key Control on FS-PC to control the program over the Network
5) For Button Control with Joystick to control the program over the Network, just use
instead the “Buttons + Switches” section for set up.
Using the Offset 6DB3, 1 Byte length
- Cursor Up  = Bit0 (Parameter x01)
- Cursor Down  = Bit1 (Parameter x02)
- Enter  = Bit2 (Parameter x04)
- Display Hide/Visible  = Bit3 (Parameter x08), but needs to be Togglebits – without “Control sent
when main Key released” definition !!
Setting in FSUIPC for Cursor UP, Bit0 (2^0 = 1)
Setting in FSUIPC for ENTER, Bit2 (2^2 = 4)
www.technicalservicerichter.com Page 56
TSR B737 SwitchSound
The B737 SwitchSound lets you hear on each switch state change on the B737 Overhead Panel a switch
sound.
This software is for those they use e.g. a Touch Screen for the overhead panel and need to hear that a
switch has been really touched.
The program starts minimized and connects to WideClient or FSUIPC direct. When pmSystems (Project
Magenta) is running it recognized each switch state change and plays a sound.
There are 4 different sound defined you can change in its ini file.
[TSR B737 SwitchSound]
Sound file Switch Normal =switch_large
Sound file Switch Center =switch_large
Sound file Switch Rotary =switch_rotary
Sound file Switch Button =switch_small
The attached sound files are taken from FS9 (Microsoft ‡ Flight Simulator 2004) as examples and are not
part of the software.
To change the sound files just write the new name (without “.wav”) in the corresponding line.
Normal = there are normal switches with ON / OFF position defined
Center = there are switches with a center position defined
Rotary = there are rotary switches like the engine starter switch defined
Button = there are momentary button switches like Groundcall defined
www.technicalservicerichter.com Page 57
ICAO Position
It is this one is required or contained around a program addition as of Boeing 737-
NG version 7472.86.225.50.
Far more than 26,000 airport positions have been saved internally with
corresponding ICAO codes for each Flight Simulator, FSX and FS2004!
With this additional program, what will be opened and closed by TSR AutoBrake
program automatically you can for your needed airports define for its corresponding
landing directions RWY conditions.
Conditions means here that the braking acceleration counted in TSR AutoBrake will
be in addition increased or decreased up to 40%.
There can be e.g. RWY’s with slope or downward slope (like Lukla) or just good or
bad surface simulated, they are actually not available in FS.
After opening the ICAO.txt file by clicking on Open ICAO.txt by following the exact
syntax values are inserted or changed.
[ICAO],[direction],[factor]
factor 00/10=norm, 01-09=bad/sloped negative, 11-20=good/sloped
ICAO = the ICAO of airports, e.g. VNLK for Lukla. For installed Lukla Scenery
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料17(103)