5. Close-up
________
(Ref. Fig. 301/TASK 12-22-27-991-003)
Subtask 12-22-27-410-053
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Close the access door 312AR.
Subtask 12-22-27-865-055
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit
breaker(s): R 19CE1, 19CE2, 19CE3.
Subtask 12-22-27-942-053
C. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R **ON A/C 001-049, 051-061, 101-103, 201-203, 301-399,
TASK 12-22-27-640-004
Lubrication of all Flap Track Carriage Rollers
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 275446-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice
No specific access platform 3.5 m (11 ft. 6 in.)
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 12-22-27Page 308 1301-399, 1May 01/05 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I
SYNTH.ESTER BASED GREASE HIGH PRESSURE
(Ref. 20-31-00)
Material No. 04-024 AIB AIMS 09-06-001
SYNTHETIC GREASE FOR FLAP & SLAT MECHANISM
(Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground
27-50-00-866-009 Retraction of the Flaps on the Ground
SIL 12-008 (for corrective action)
R **ON A/C 001-049, 051-061, 101-103, 201-203,
12-22-27-991-001 Fig. 302
**ON A/C 301-399,
12-22-27-991-001-A Fig. 302A
R **ON A/C 001-049, 051-061, 101-103, 201-203, 301-399,
3. Job Set-up
__________
R **ON A/C 001-049, 051-061, 101-103, 201-203,
(Ref. Fig. 302/TASK 12-22-27-991-001)
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 12-22-27Page 309 1301-399, 1May 01/05 1 1 1CES 1
Flap Track Carriage Rollers - Lubrication Points
Figure 302/TASK 12-22-27-991-001
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 12-22-27Page 310 1 1 May 01/05 1 1 1CES 1
**ON A/C 301-399,
(Ref. Fig. 302A/TASK 12-22-27-991-001-A) R **ON A/C 001-049, 051-061, 101-103, 201-203, 301-399,
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM SERVICING 2(3)
