Material No. 04-004  USA MIL-PRF-23827 TYPE I
 SYNTH.ESTER BASED GREASE HIGH PRESSURE
 (Ref. 20-31-00)

 Material No. 04-017  USA A-A-59173
 SILICONE GREASE (Ref. 20-31-00)

 Material No. 05-027  USA MIL-L-81309
 RUST INHIBITOR(FOR CORROSION USE 15-004)
 (Ref. 20-31-00)

 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-30-00-860-001  Open the FWD or AFT Cargo-Compartment Door with the
 Yellow Electric Pump
 52-31-13-000-001 Removal of the Lining and the Insulation
 52-32-13-000-001 Removal of the Lining and Insulation

R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
 12-22-52-991-014-A  Fig. 308
 **ON A/C 051-052,
 12-22-52-991-014  Fig. 308A **ON A/C ALL

 3. Job Set-up
__________ R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
 Subtask 12-22-52-010-065-A
 A. Get Access
 (Ref. Fig. 308/TASK 12-22-52-991-014-A)

 (1)
 Open the FWD and/or AFT cargo-compartment door (referred to as cargo door) and safety it with the actuator safety locks (Ref. TASK 52-30-00-860-001).

 (2)
 Put the adjustable access platform in position below the opened cargo door.

 (3)
 Remove the door lining and insulation from the applicable cargo door to get access to inner skin (Ref. TASK 52-31-13-000-001) or (Ref. TASK 52-32-13-000-001).

 (4)
 Remove the screws and access cover from the inner skin of the cargo door.

 **ON A/C 051-052,
 Subtask 12-22-52-010-065
 A. Get Access
 (1)
 Put the access platform in position below the closed FWD or AFT cargo compartment door (referred to as cargo door).

 (2)
 Remove the access panel 825AR or 826AR from the cargo door.

 (3)
 Push the handle flap in and pull the locking handle away from the cargo door.

 NOTE : Do not move the locking handle in the UNLOCKED position at
____
 this time.

 Lubrication of the FWD and AFT Cargo Compartment-Door Handle Figure 308/TASK 12-22-52-991-014-A
R 1EFF : 001-049, 053-099, 101-149, 151-199, 1 12-22-52Page 335 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 **ON A/C ALL

 Subtask 12-22-52-865-052
 B. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU HYDRAULIC/HYD POWER/Y 3803GX N30 122VU DOORS/CARGO 1MJ T12 123VU Y HYD/ELEC/PUMP 3802GX AB06 123VU Y HYD/ELEC/ELEC PUMP/NORM 3801GX AB03
 4. Procedure
_________
R **ON A/C 001-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
 Subtask 12-22-52-640-058-A
 A. Lubrication of the Door Handle
 (Ref. Fig. 308/TASK 12-22-52-991-014-A)

 (1)
 Apply COMMON GREASE (Material No. 04-004) or to the grease nipple of the door handle shaft.

 (2)
 Apply OILS (Material No. 03-001) to the pivot points of the door handle flap.

 (3)
 Apply COMMON GREASE (Material No. 04-017) to the mating surface of the Malteser-cross latch and the Malteser-cross lock.

 (4)
 Remove the unwanted grease or oil with a lint-free cloth.

 WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES AND GOGGLES.
 (5) Apply SPECIAL MATERIALS (Material No. 05-027) to the inner surfaces and the adjacent area of the locking handle (2).

R  **ON A/C 051-052, 
R  Subtask 12-22-52-640-058 
R  A. Lubrication of the Locking Handle 
R  (Ref. Fig. 308A/TASK 12-22-52-991-014) 
R  (1) Apply COMMON GREASE (Material No. 04-004) or to the grease nipple (2) 
R  of the locking handle (3). 
R  (2) Apply OILS (Material No. 03-001) to the pivot points (1) of the 
R  locking handle (3). 
R  (3) Apply OILS (Material No. 03-001) to the pivot points of the handle 
R  flap mechanism (4). 
R  (4) Apply OILS (Material No. 03-001) to the pivot points of the locking 
R  handle spring. 
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM SERVICING 2(30)