曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 1 Flight plan initialization, takeoff and wind data auto-print
_ If ACARS is installed, with the corresponding ACARS datalink function enabled for the current FM/ACARS configuration and if the "Auto-Print of ACARS Uplink" option is enabled within the Nav data base policy file, the automatic print status may be either YES or NO, preceded by a selection star. It is defaulted as selected within the Nav data base policy file for the corresponding function and is modifiable by the crew. If an ACARS function is disabled for the current FM/ACARS configuration, then no automatic printing of uplinks can occur for this function. Nevertheless, manual printing of active data is still allowed for this function. When in the *NO state, automatic printing is not activated for the associated ACARS function when the uplink is received. When in the *YES state, automatic printing is activated when the uplink is received.

 DATA INDEX (with ACARS installed)
 Figure 012

 

 PRINT FUNCTION Page 1 (with ACARS Takeoff Data Uplink Disabled and Auto Print
 of Wind Uplink Disabled)

 Figure 013 
R 1EFF : 062-099, 151-199, 201-212,  1 22-76-00 Page 33 
1  1  Config-1 May 01/05
 1  1
 1CES  1

 

 PRINT FUNCTION Page 2 (with Auto Print at Transition to Takeoff Disabled and Pre-Flight Report Available)
 Figure 014 
R 1EFF : 062-099, 151-199, 201-212,  1 22-76-00 Page 34 
1  1  Config-1 May 01/05
 1  1
 1CES  1

 

 2
_
 3
_
 4
_
 The automatic print state toggles to the other state (if the selection star exists) when pressing the left line selection key, whether on ground or in flight. Pushing the left line key without a selection star results in the NOT ALLOWED message.
Flight report auto-print For the pre-flight, in-flight and post-flight reports, the YES or NO prompts with a preceding selection star are displayed if the Auto-Print of Flight Reports option is enabled within the Nav data base policy file. If this option is not enabled, NO without a selection star is displayed. They are not dependent on whether or not ACARS is installed. If this option is enabled, then the *YES or *NO state defaults as selected within the Nav data base policy file for the report. For the pre-flight report, YES is displayed if the "Autoprint at Engine Start" option is enabled; otherwise *NO is displayed. For the in-flight report, the "Autoprint at Transition to Takeoff" option is used. For the post-flight report, the "Autoprint at Engine Shut Down" option is used. These defaults can be manually overwritten by prompt reselection if the "Auto Print of Flight Reports" option is enabled. Pushing the line key adjacent to the prompt toggles to the other state.
Manual printing For each line, the right side allows manual printing for the corresponding function, even if not enabled for ACARS or for automatic printing. When a PRINT selection is performed, the corresponding report is sent to the printer and the star is removed from the display until the data are printed or a printer communication error occurs. In either case, the star is displayed again. When a flight report or an ACARS uplink report is being automatically printed, the corresponding manual print selection star is removed from display. The manual print selection star is not displayed if the FM is unable to communicate with the printer.
Report printing Selection of a prompt without a star displayed next to it is rejected and results in a NOT ALLOWED message.
 -F-PLN INIT Print Selection of a PRINT prompt with a star adjacent to the F-PLN initialization function prints the current active flight plan and performance data.
 -TO DATA Print  Selection of a PRINT prompt with a star adjacent to the takeoff data function prints the current active takeoff data for the active flight plan runway and airport.

 -WIND DATA Print Selection of a PRINT prompt with a star adjacent to the Wind Data function prints the current active climb, cruise and descent wind data for the active flight plan.
 -PREFLIGHT Print Selection of a PRINT prompt with a star adjacent to the Preflight function prints the Preflight Report. The PRINT selection star for this function is displayed only if Preflight Report is available.
 -INFLIGHT Print Selection of a PRINT prompt with a star adjacent to the inflight function prints the inflight Report. The PRINT selection star for this function is displayed only if inflight Report is available.
 -POSTFLIGHT Print Selection of a PRINT prompt with a star adjacent to the Postflight function prints the Postflight Report. The PRINT selection star for this function is displayed only if Postflight Report is available.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AUTO FLIGHT 自動飛行4(64)