-
TEST FAILURE:
 An anomaly has been detected during the test.

R  **ON A/C 106-149, 151-199, 201-299, 301-399, 401-499, Post SB 31-1130 For A/C 201-203,
 H. MDDU Interface (Messages)
 A 16-character display permits communications between the operator and the data loader. The messages inform the operator of the transfer status 12 messages can be displayed, one at a time.
R 1EFF : 106-149, 151-199, 201-299, 301-399, 1 31-38-00Page 33 1401-499, 1Config-2 Aug 01/05 1 1 1CES 1 These messages are:

 -MDDU READY:
 when the data loader has performed a power on self-test and if no
 anomaly is detected, this message is displayed.

 -READY:
 A disk is inserted in the loader drive. The equipment is ready. This message acknowledges disk insertion.
 -WAIT RESPONSE:
 This message is displayed when the data loader is waiting for a
 response from the computer at initialization.
 This situation may arise for various reasons:

 -
the computer is not power supplied or is out of order

 -
the data loading selector is set to the wrong computer

 -
the configuration file is not correct (e.g. wrong system address label etc.)

 -
the LGCIU1 is not power supplied (the target computer does not receive the ground indicating that it is in load mode).

 NOTE : This message can be displayed indefinitely, without display of an
____ anomaly message.
 -TRANS FAILURE:
 If the data loader has to stop data transfer (up or down loading) for any reason (time-out, bad checksum, etc.) this message is displayed. The data loader can be reset by a RESET command or by a power-on routine after the anomaly has been corrected, or by removing and inserting the disk.
 -UNIT FAIL:
 The data loader displays this message if a hardware failure is detected during the self-test. In this case, the data loader stops all operations.
R 1EFF : 106-149, 151-199, 201-299, 301-399, 1 31-38-00Page 34 1401-499, 1Config-2 Aug 01/05 1 1 1CES 1 NOTE : The maintenance messages concerning the MDDU can be consulted on

____ the SYSTEM REPORT TEST CFDS page (Ref. para. BITE).
 -DISK ERROR:
 If the data loader cannot read or write data on the disk (incorrect
 formatting, write-protected, disk damaged, etc.) it will interrupt
 operations and display this message.

 -EJECT DISK and INSERT NEXT DISK:
 When the volume of data to be transferred is large and requires several disks, these messages (shown one after the other) inform the operator that the disk must be changed.
 -DISK CHANGE: Disk not compatible with the configuration file.
 -
TRANSF COMPLETE:

 When data transfer between the data loader and the computer has been successfully completed, this message is displayed to indicate the end of the transfer.

 -
TRANSF IN PROG:

 The data loader is in communication with the computer concerned when data transfer operations are completed.
 -BUS N: XXXXXXX (a BUS number appears with a decrementer): This permits to display the progress of the uploading and shows that
 uploading is not stopped because of a failure. NOTE : The N indication is the number of the bus in transfer (from 1 to
____ 8). The XXXXXXX indication is the number of bytes or the remaining bytes to be transferred.
 -TEST IN PROGRESS: The disk inserted in the loader is identified as a test disk. The data
 loader is in test mode. NOTE : The disk should not be extracted while TRANSF IN PROG and TEST IN
____ PROGRESS messages are displayed as damage to the disk could result.
R 1EFF : 106-149, 151-199, 201-299, 301-399, 1 31-38-00Page 35 1401-499, 1Config-2 Aug 01/05 1 1 1CES 1

 -
TEST COMPLETED:
 The test is over and no anomaly has been detected.

 -
TEST FAILURE:

 An anomaly has been detected during the test. R **ON A/C 106-149, 151-199, 201-299, 301-399, 401-499,
 J. Data Loading Selector (DLS) Interface (Messages)
 A LCD backlighted screen composed of two lines of 16 characters of target computers and the state of its link with the disk unit. NOTE : The blinking of the display (2 or 3 times) is due to an action or
____
 a none autorized key.

 (1) Name and state of LRUs (SELECTED / NOT SELECTED)
 (a) List of message steps when going through the menu with PREV/NEXT key.
 -DLRB
 NOT SELECTED

 NOTE : When this display flashes , two or three time, shows that
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 指示/記錄系統 5(126)