REFERENCE DESIGNATION
-------------------------------------------------------------------------------
32-11-12-400-001 Installation of the MLG Hydraulic Dressings 32-11-43-000-001 Removal of the 1M and 2M Harnesses from the MLG Leg 32-11-43-400-002 Installation of the 1M and 2M Harnesses on the MLG
Leg
32-11-00-991-018 Fig. 603
32-11-00-991-019-B Fig. 604
**ON A/C 001-003, 051-052,
32-11-00-991-021 Fig. 605
R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
32-11-00-991-021-A Fig. 605A
**ON A/C ALL
3. Job Set-up
__________
Subtask 32-11-00-941-074
A. Safety Precautions
(1)
Make sure that the ground safety locks are installed on the landing gear (Ref. TASK 32-00-00-481-001).
(2)
On the panel 400VU:
-make sure that the landing-gear control-lever 6GA is in the DOWN position
-put a warning notice in position to tell persons not to operate the landing gear.
(3)
Put warning notices in position to tell persons not to operate the landing gear doors.
(4)
Put the safety barriers in position.
1EFF : ALL 1 32-11-00Page 618 1 1 Aug 01/05 1 1 1CES 1 Subtask 32-11-00-869-055
B. Flight Configuration Precautions
(1)
If the electrical power is not necessary for other maintenance tasks, de-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
(2)
If the electrical power is necessary, do the precautions for flight configuration (Ref. TASK 32-00-00-860-001) before you lift the aircraft.
Subtask 32-11-00-582-053
C. Lift the Aircraft
(1) Lift the aircraft on jacks (Ref. TASK 07-11-00-582-002).
Subtask 32-11-00-010-064
D. Get Access
(1) Put the access platform adjacent to the applicable MLG.
4. Procedure
_________
(Ref. Fig. 603/TASK 32-11-00-991-018, 604/TASK 32-11-00-991-019-B)
**ON A/C 001-003, 051-052,
(Ref. Fig. 605/TASK 32-11-00-991-021) R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 605A/TASK 32-11-00-991-021-A)
1EFF : ALL 1 32-11-00Page 619 1 1 Aug 01/05 1 1 1CES 1
MLG Inspection Areas Figure 603/TASK 32-11-00-991-018
1EFF : 1 1R 1CES ALL 1 11 1 32-11-00 Page 620 Nov 01/04
R MLG Side Stay Inspection Areas Figure 604/TASK 32-11-00-991-019-B
1EFF : 1 1 1CES ALL 1 111 32-11-00 Page 621 Nov 01/04
MLG Torque Link Inspection Areas
Figure 605/TASK 32-11-00-991-021
R 1EFF : 001-003, 051-052, 1 32-11-00Page 622 1 1 May 01/05 1 1 1CES 1
MLG Torque Link Inspection Areas
Figure 605A/TASK 32-11-00-991-021-A
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 32-11-00Page 623 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
**ON A/C ALL
Subtask 32-11-00-220-061
A. Out-of-Roundness Dimensional Check of the MLG Shock-Absorber Sliding-Tube
(1)
At the point X, 125 mm (5.0 in) from the MLG axle center-line, measure the out-of-roundness of the MLG sliding tube. The sliding tube must be round within 40 microns (1600 micro-inches).
(2)
At the point Y, 600 mm (23.5 in.) from the MLG axle center-line, measure the out-of-roundness of the MLG sliding tube. The sliding tube must be round within 40 microns (1600 micro-inches).
Subtask 32-11-00-220-062
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架1(104)
