-corrosion
-wear
-damage to the protective treatment.
(3)
If you find wear or damage, refer to (Ref. CMM 321222) for repair procedures.
**ON A/C ALL
5. Close-up
________ Subtask 32-11-00-586-054
A. Lower the Aircraft
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Lower the aircraft (Ref. TASK 07-11-00-586-002).
1EFF : ALL 1 32-11-00Page 650 1 1 Feb 01/05R 1 1 1CES 1
Subtask 32-11-00-942-079
B. Removal of Equipment
(1)
Close the main gear doors (Ref. TASK 32-12-00-410-001).
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 32-11-00Page 651 1 1 Feb 01/05R 1 1 1CES 1
TASK 32-11-00-200-009
Detailed Inspection of MLG, Main Fitting
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 321103-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific adjustable access platform No specific safety barriers No specific warning notice 460005835 1 GROUND LOCK SLEEVE
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1 SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
1EFF : ALL 1 32-11-00Page 652 1 1 Feb 01/05R 1 1 1CES 1
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-00-00-481-001 Installation of the Safety Devices on the Landing
Gears
32-12-00-010-001 Open the Main Gear Doors for Access
32-12-00-410-001 Close the Main Gear Doors after Access
CMM 321133 (for corrective action)
CMM 321222 (for corrective action)
CMM 321225 (for corrective action)
**ON A/C 001-003, 051-052,
32-11-00-991-029 Fig. 610
R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
32-11-00-991-029-A Fig. 610A
**ON A/C ALL
3. Job Set-up
__________
Subtask 32-11-00-941-079
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Make sure that the ground safety locks are on the landing gear (Ref. TASK 32-00-00-481-001).
(3)
On the panel 400VU:
-make sure that the landing-gear control-lever 6GA is in the DOWN position
-put a warning notice in position to tell persons not to operate the landing gear controls.
1EFF : ALL 1 32-11-00Page 653 1 1 Aug 01/05 1 1 1CES 1 Subtask 32-11-00-010-071
B. Get Access
(1)
Open the main gear (MLG) doors (Ref. TASK 32-12-00-010-001).
(2)
Make sure the GROUND LOCK SLEEVE (460005835) is on the applicable MLG door actuator.
(3)
Put the adjustable access platform below the applicable MLG leg.
4. Procedure
_________
**ON A/C 001-003, 051-052,
(Ref. Fig. 610/TASK 32-11-00-991-029) R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 610A/TASK 32-11-00-991-029-A)
**ON A/C 001-003, 051-052,
Subtask 32-11-00-200-051
A. Detailed Inspection of MLG, Main Fitting
(1)
Preparation for inspection:
(a) Use a clean MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean the areas to be examined. 中國航空網(wǎng) www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM LANDING GEAR 起落架1(112)
