1EFF : ALL 1 32-11-00Page 637 1 1 Feb 01/05R 1 1 1CES 1

R  MLG Side-Stay Attachment Lug - Inspection Area Figure 607/TASK 32-11-00-991-020
 1EFF : 1 1 1CES  ALL  1 111 32-11-00 Page 638 Nov 01/04

 5. Close-up
________ Subtask 32-11-00-410-064
 A. Close Access
 (1) Install the side-stay lower cardan joint and connect the side-stay (Ref. TASK 32-11-18-400-001).
 Subtask 32-11-00-942-077
 B. Removal of Equipment
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.

 (2)
 Remove the warning notice(s).

 (3)
 Remove the access platform(s).

 (4)
 Remove the safety barriers.

 (5)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 1EFF : ALL 1 32-11-00Page 639 1 1 Feb 01/05R 1 1 1CES 1

 TASK 32-11-00-200-007
 Inspection of the MLG Axles after a Brake Overheat
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE LANDING GEAR ARE CLEAR.
_______
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific abrasive paper (320 to 500 grit)
 No specific hardness tester (MICRODUR unit or equivalent)
 No specific safety barriers
 No specific warning notices

 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-00-00-864-001 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action 32-00-00-481-001 Installation of the Safety Devices on the Landing Gears 32-41-11-000-006 Removal of the MLG Wheel (2649GM,2650GM,2651GM,2652GM) 32-41-11-400-006 Installation of the MLG Wheel
 (2649GM,2650GM,2651GM,2652GM) 32-42-27-000-001 Removal of the Brake (2641GM,2642GM,2643GM,2644GM) 32-42-27-400-001 Installation of the Brake
 (2641GM,2642GM,2643GM,2644GM)
 1EFF : ALL 1 32-11-00Page 640 1 1 Feb 01/05R 1 1 1CES 1

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
CMM 321133 (for corrective action) CMM 321222 (for corrective action) CMM 321225 (for corrective action) 32-11-13-000-004 Removal of the Sliding Tube Sub-Assembly of the MLG
 Shock Absorber (for corrective action) 32-11-13-400-004 Installation of the Sliding Tube Sub-Assembly of the MLG Shock Absorber (for corrective action) 32-11-00-991-023 Fig. 608
 3. Job Set-up
__________
 Subtask 32-11-00-941-077
 A. Safety Precautions
 (1)
 Make sure that the ground safety locks are on the landing gear (Ref. TASK 32-00-00-481-001).

 (2)
 On the panel 400VU:

 -make sure that the landing gear control lever 6GA is in the DOWN position
 -put a warning notice in position to tell persons not to operate the landing gear.

 (3)
 Put warning notices in position to tell persons not to operate the landing gear doors.

 (4)
 Put the safety barriers in position.

 (5)
 Make sure that the Green and the Yellow hydraulic systems are depressurized (Ref. TASK 29-00-00-864-001).

 Subtask 32-11-00-010-067
 B. Get Access
 (1)
 Remove the MLG wheels (Ref. TASK 32-41-11-000-006).

 (2)
 Remove the axle protection sleeves and the brakes (Ref. TASK 32-42-27-000-001).

 1EFF : ALL 1 32-11-00Page 641 1 1 Feb 01/05R 1 1 1CES 1

 4. Procedure
_________
 (Ref. Fig. 608/TASK 32-11-00-991-023)
 Subtask 32-11-00-210-073
 A. Visual Inspection
 (1)
 Make sure the paint is in good condition on the brake flange and between the axle sleeve lands.

 (2)
 Make sure the paint is in good condition on the surface of the axle bore.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架1(109)