C. Expendable Parts
-------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION |IPC-CSN
-------------------------------------------------------------------------------
6 cotter pins 32-11-11 82 -170 6 cotter pins 32-11-11 82C-170 6 cotter pins 32-11-11 82D-170
D. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
20-28-00-720-005 Check of the Electrical Bonding of the Different Components (But not the Fluid Systems and the Components Installed on Composite materials)
29-00-00-864-001 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action 29-23-00-860-001 Disconnection of the Isolation Coupling of the Power Transfer Unit (PTU) 29-23-00-860-002 Connection of the Isolation Coupling of the Power Transfer Unit (PTU) 32-00-00-481-001 Installation of the Safety Devices on the Landing Gears 32-00-00-860-001 Flight Configuration Precautions with Electrical Power 32-00-00-860-002 Ground Configuration after Flight Configuration with Electrical Power 32-31-00-820-003 Adjustment of the MLG Uplock
**ON A/C 001-003, 051-052,
32-11-11-991-028 Fig. 408
R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
32-11-11-991-028-A Fig. 408A
1EFF : ALL 1 32-11-11Page 486 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL
3. Job Set-up
__________
Subtask 32-11-11-941-062
A. Safety Precautions
(1)
Make sure the safety barriers are in position.
(2)
On the panel 400VU:
-
make sure that the landing-gear control-lever 6GA is in the DOWN position
-
make sure that warning notices are in position to tell persons not to operate the landing gear.
-
make sure that warning notices are in position to tell persons not to operate the main gear doors.
(3)
Make sure that a warning notice is in the cockpit to tell persons not to pressurize the Green hydraulic system.
(4)
Make sure that the ground safety locks are installed on the landing gear (Ref. TASK 32-00-00-481-001).
Subtask 32-11-11-860-070
B. Aircraft Maintenance Configuration
(1)
If applicable, make sure that the flight configurations were obeyed (Ref. TASK 32-00-00-860-001).
(2)
Make sure that the Green and Yellow hydraulic systems are depressurized. (Ref. TASK 29-00-00-864-001).
(3)
Make sure that the isolation coupling on the PTU is disconnected (Ref. TASK 29-23-00-860-001).
(4)
Make sure that the access platform is in position below the applicable zone 731(741).
R 1EFF : ALL 1 32-11-11Page 487 1 1 Aug 01/05 1 1 1CES 1 Subtask 32-11-11-865-064
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU L/G/LGCIU/SYS1/NORM 1GA C09 121VU HYDRAULIC/LGCIU/SYS2 2GA Q35 121VU HYDRAULIC/LGCIU/SYS1/GRND SPLY 52GA Q34
4. Procedure
_________
**ON A/C 001-003, 051-052,
(Ref. Fig. 408/TASK 32-11-11-991-028)
R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
(Ref. Fig. 408A/TASK 32-11-11-991-028-A)
**ON A/C 001-003, 051-052,
Subtask 32-11-11-420-079
A. Preparation for Installation
(1)
Use a MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean the components and component interface.
(2)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(3)
Apply SPECIAL MATERIALS (Material No. 05-047) to:
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架1(141)
