C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
07-11-00-581-001 Lifting for Aircraft Maintenance Operations 07-11-00-586-002 Lowering of the Aircraft for Maintenance Operations 32-00-00-481-001 Installation of the Safety Devices on the Landing
Gears 32-00-00-860-001 Flight Configuration Precautions with Electrical
Power 32-12-00-010-001 Open the Main Gear Doors for Access 32-12-00-410-001 Close the Main Gear Doors after Access CMM 321133 (for corrective action) CMM 321222 (for corrective action) CMM 321225 (for corrective action) 32-11-00-991-028 Fig. 609
3. Job Set-up
__________
Subtask 32-11-00-941-078
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Make sure that the ground safety locks are on the landing gear (Ref. TASK 32-00-00-481-001).
(3)
On the panel 400VU:
-make sure that the landing-gear control-lever 6GA is in the DOWN position
-put a warning notice in position to tell persons not to operate the landing gear controls.
Subtask 32-11-00-860-058
B. Aircraft Maintenance Configuration
(1)
Open the main gear doors (Ref. TASK 32-12-00-010-001).
(2)
Make sure the GROUND LOCK SLEEVE (460005835) is on the applicable main gear door actuator.
(3)
Do the flight configuration precautions procedure (Ref. TASK 32-00-00-860-001).
1EFF : ALL 1 32-11-00Page 647 1 1 Feb 01/05R 1 1 1CES 1
Subtask 32-11-00-581-050
C. Lifting of the Aircraft
(1) Lift the aircraft on jacks (Ref. TASK 07-11-00-581-001).
4. Procedure
_________
(Ref. Fig. 609/TASK 32-11-00-991-028)
**ON A/C 001-003, 051-052,
Subtask 32-11-00-200-050
A. Detailed Inspection of MLG Sliding Tube
(1)
Preparation for inspection:
(a) Use a clean MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean the area to be examined.
(2)
Examine the MLG sliding tube for:
-corrosion
-wear
-damage to the protective treatment.
(3)
If you find wear or damage, refer to (Ref. CMM 321133) for repair procedures.
R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 401-499,
Subtask 32-11-00-200-050-A
A. Detailed Inspection of MLG Sliding Tube
(1) Preparation for inspection:
(a) Use a clean MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean the area to be examined.
1EFF : ALL 1 32-11-00Page 648 1 1 Aug 01/05 1 1 1CES 1
MLG Sliding Tube Inspection Areas Figure 609/TASK 32-11-00-991-028
1EFF : 1 1R 1CES ALL 1 11 1 32-11-00 Page 649 Feb 01/05
(2)
Examine the MLG sliding tube for:
-corrosion
-wear
-damage to the protective treatment.
(3)
If you find wear or damage, refer to (Ref. CMM 321225) for repair procedures.
**ON A/C 301-399,
Subtask 32-11-00-200-050-B
A. Detailed Inspection of MLG Sliding Tube
(1)
Preparation for inspection:
(a) Use a clean MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean the area to be examined.
(2)
Examine the MLG sliding tube for:
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架1(111)
