(b)
On the panel 2000VU, set the MAINT BUS switch to the ON position.
1EFF : ALL 1 32-00-00Page 218 1 1 May 01/05 1 1 1CES 1
TASK 32-00-00-860-001- 01 Flight Configuration Precautions without Electrical Power WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
To isolate electrical power to prevent flight configuration when you do maintenance tasks on the A/C. NOTE : Do this task only if electrical power is not necessary for subsequent
____ maintenance tasks. If electrical power is necessary, do the Flight Configuration Precautions with Electrical Power procedure (Ref. TASK 32-00-00-860-00100).
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-00-00-860-001 Ground Configuration after Flight Configuration without Electrical Power
3. Job Set-up
__________
1EFF : ALL 1 32-00-00Page 219 1 1 Feb 01/05R 1 1 1CES 1
R 4. Procedure_________
R Subtask 32-00-00-860-067
R A. Aircraft Maintenance Configuration
R (1) On the ELEC panel 35VU, set the EXT PWR pushbutton switch to the OFF
R position.
R (2) On the panel 2000VU, set the MAINT BUS switch to the OFF position.
R NOTE : The aircraft electrical system is isolated to prevent flight____
R configuration.
R Subtask 32-00-00-869-065
R B. Put the Aircraft Back to the Ground Configuration
R (1) When you have done the maintenance tasks necessary, do the ground
R configuration after flight configuration without electrical power
R procedure (Ref. TASK 32-00-00-860-001).
1EFF : ALL 1 32-00-00Page 220 1 1 Nov 01/04 1 1 1CES 1
TASK 32-00-00-860-001- 02 Ground Configuration after Flight Configuration without Electrical Power WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
To put the aircraft back to the correct (ground) configuration after it was in a flight configuration without electrical power. NOTE : Do this task only if you have done the Flight Configuration
____
Precautions without Electrical Power procedure (Ref. TASK
32-00-00-860-00101).
2.
Job Set-up Information
______________________
Not Applicable
3.
Job Set-up
__________
4.
Procedure
_________ Subtask 32-00-00-860-065
A. Aircraft Maintenance Configuration
(1)
On the ELEC panel 35VU, set the EXT PWR pushbutton switch to the ON position.
(2)
On the panel 2000VU, set the MAINT BUS switch to the ON position.
1EFF : ALL 1 32-00-00Page 221 1 1 Feb 01/05R 1 1 1CES 1
TASK 32-00-00-860-003
To Put the Landing Gear System back to the Normal Mode after a Free-Fall Extension
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
To put the landing gear system back to the normal mode after the free-fall system has been operated in flight (and the landing gear and doors safetied Ref. TASK 32-00-00-481-003).
2. Job Set-up Information
______________________
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM LANDING GEAR 起落架1(84)
