(3)
 Make sure that all bushes are in the correct condition.

 (4)
 Apply COMMON GREASE (Material No. 04-004) to all surfaces of parts which move.

 Subtask 52-22-21-420-053
 B. Installation of the Locking Hook Assembly
 (Ref. Fig. 404/TASK 52-22-21-991-003)

 (1) If removed, install the connection rod (118) to the locking hook
 (107) as follows:
 (a)
 If removed, install the bush (116) to the locking hook (107).

 (b)
 Put the eye-end of the connection rod (118) in position at the locking hook (107).

 1EFF : 301-399, 1 52-22-21Page 438 1 1 May 01/04 1 1 1CES 1

 (c)
 Install the bolt (106), the washers (112), the bush (117) and the nut (111) to the locking hook (107).

 (d)
 Tighten the nut (111) and safety it with the cotter pin (110).

 (2)
 If removed, install the bellows (114) to the connection rod (118) and attach it with the tie-wrap (113).

 (3)
 Connect the locking hook (107) to the door fitting (103) as follows:

 (a)
 Put the locking hook (107) together with the connection rod (118) and the bellows (114) in position to door fitting (103).

 (b)
 Put the washers (108) and (109) in position and attach the locking hook (107) with the sleeve (102) on the door fitting (103).

 (c)
 Install the bolt (105), the washer (104) and the nut (101) to the door fitting (103).

 (4)
 Install the bellows (114) on the door fitting (103) and attach it with the tie-wrap (115).

 (5)
 Connect the connection rod (118) with the actuation lever (123) as follows:

 (a)
 If removed, install the bush (120) to the actuation lever (123).

 (b)
 Put the eye-end of the connection rod (118) in position to the actuation lever (123).

 (c)
 Install the bolt (122), the washers (121), the bush (119) and the nut (125) to the actuation lever (123).

 (d)
 Tighten the nut (125) and safety it with the new cotter pin (124).

 Subtask 52-22-21-420-054
 C. Installation of the Drift Pin Assembly
 (Ref. Fig. 404/TASK 52-22-21-991-003)

 (1) If removed, install the spring unit (154) as follows: WARNING : BE CAREFUL WHEN YOU REMOVE OR INSTALL THE SPRING. THE
_______ TENSION IN THE SPRING CAN CAUSE INJURY TO PERSONS.
 1EFF : 301-399, 1 52-22-21Page 439 1 1 May 01/04 1 1 1CES 1

 (a)
 Put the upper eye-end of the spring unit (154) in position to the fork end of the twin lever (152).

 (b)
 Install the bolt (151), the washers (150), the bushes (153) and the nut (148) to the twin lever (152).

 (c)
 Tighten the nut (148) and safety it with the cotter pin (149).

 (d)
 Put the fork-end of the spring unit (154) in position to the fitting (156) and attach it with the pin (155).

 (e)
 Safety the pin (155) with the washer (157) and the new cotter pin (158).

 (2)
 Install the drift pin assembly (128) as follows:

 (a)
 Put the drift pin assembly (128) in position to the upper member (132).

 (b)
 Attach the guide fitting (127) with the bolts (134) and the washers (133) to the upper member (132).

 (3)
 Connect the fork link (139) with the drift pin (128) as follows:

 (a)
 If removed, install the bush (135) to the fork link (139).

 (b)
 Put the fork link (139) in position to the eye- end of the drift pin (129).

 (c)
 Install the bolt (140), the washers (138), the spacer (130), the bush (131) and the nut (137) to the fork link (139).

 (d)
 Tighten the nut (137) and safety it with the new cotter pin (136).

 (4)
 Connect the fork link (139) with the twin lever (152) as follows:

 (a)
 If removed, install the bush (146) to the fork-end (139).

 (b)
 Put the fork link (139) in position at the twin lever (152).

 (c)
 Install the bolt (147), the washers (143), the bush (144), the spacer (145) and the nut (142) to the fork link (139).

 (d)
 Tighten the nut (142) and safety it with the cotter pin (141).

 1EFF : 301-399, 1 52-22-21Page 440 1 1 May 01/04 1 1 1CES 1 Subtask 52-22-21-420-055

 D. Installation of the Locking Shaft Assembly
 (Ref. Fig. 405/TASK 52-22-21-991-004)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門3(121)